Anybody Using A Kabuki?

[DPLongo22]

In a Kabuki jar would work.......

MUCH too small. I/we've been at this for a bit of time, ya?

 

[ENAUD]

In a Kabuki jar would work.......

NO! Kabuki jars are for soaking atties during cleaning

 

[Stormy1960]

............

 

[cllmda]

Yes, the tube that is attached to the top of the coil can collect debris.


Sent from my iPhone using Tapatalk

what would u suggest then ? would a few rounds in the ultrasonic cleaner do it ? or letting it soak in alcohol overnight ?

 

[jwbnyc]

Get a cloth, or paper towel, moisten it, and ream it out.

 

[cllmda]

I have over a dozen Kabukis. I rinse them in warm water with ever coil change, which is more often than I'd like because I do use juices that tend to gunk them up. I have a small brush that was made for drip tips. I bought a set long ago off eBay. I run it down the chimney a few times and through the hole where the coil sits. I also stick a pipe cleaner through the air hole. I've notice no reduction in airflow. The airflow screw on all of mine are flush with the edge of the tank. They say you cannot, but you can remove the airflow screw and the tanks work fine.

You can run the stainless version through an ultrasonic cleaner with no ill effects. Not so with the Stealth version. I'm not sure about the Zenkote model. I think the Ti model would work OK in the ultrasonic.

thanks... that's very useful advice

Ive never seen those cleaning brushes kits for drips tips but will keep on the lookout for something that could work.

My Kabukis are all either the zenkote or the regular version , ill try putting one or two regulars thru the ultrasonic cleaner and see if there's any improvement

How long do you guys put it thru the ultrasonic cleaner for ?

 

[AstroTurf]

what would u suggest then ? would a few rounds in the ultrasonic cleaner do it ? or letting it soak in alcohol overnight ?

Brush, Pipe Cleaner, or Q-Tip...

 

[Arnold Ziffle]

I use those small brushes for cleaning between teeth to clean coils and air holes .

 

[JUMA55]

thanks... that's very useful advice

Ive never seen those cleaning brushes kits for drips tips but will keep on the lookout for something that could work.

My Kabukis are all either the zenkote or the regular version , ill try putting one or two regulars thru the ultrasonic cleaner and see if there's any improvement

How long do you guys put it thru the ultrasonic cleaner for ?

Here you go:
Mini Cleaning Brush For Drip Tips & Small Parts (Pack of 5) - FAST SHIP FROM USA

I run everything through the ultrasonic on two cycles of five minutes each. No logic behind it. Just seems to work.

 

[ravnhaus]

 

[DPLongo22]

Thanks, ravnhaus.

 

[Knifemaker]

K.D. Yes I ignored you. When you started off by telling me "Who you would NOT" watch, I figured, fine. I dont' have the time to try and help, while someone is telling me what they Won't do. Why you won't is none of my business. Nor do I care why. It's your business, and you have google just like everyone else.
You have spent far too much time dissing me in the past, and now you want my help, and before I can do so, you are already telling me what you will not do. So to please yourself, educate yourself. You can decide for yourself if the search or education is worth your while.
I don't feel like being put down if I should by chance link you to someone, or something that you are not happy happy with or about.

DPL;
The rebuilding vids I was referring to, were for the standard Nauti and Mini Triton Coils. There are also videos on the Rebuildable Decks as well. Not thrilled with any of the videos. But they did give me a reference point for starting. Then adapting the techniques for personal use.

As far as ignoring people here, I don't live on the forum. There is a life out there. And you have to admit, this thread is just about dead, in regards ot any type of useful info for quite some time now. The only time I see any real activity, it is either to put some member in their place, or completely off topic. YMMV

Knife

 

[AstroTurf]

K.D. Yes I ignored you. When you started off by telling me "Who you would NOT" watch, I figured, fine. I dont' have the time to try and help, while someone is telling me what they Won't do. Why you won't is none of my business. Nor do I care why. It's your business, and you have google just like everyone else.
You have spent far too much time dissing me in the past, and now you want my help, and before I can do so, you are already telling me what you will not do. So to please yourself, educate yourself. You can decide for yourself if the search or education is worth your while.
I don't feel like being put down if I should by chance link you to someone, or something that you are not happy happy with or about.

DPL;
The rebuilding vids I was referring to, were for the standard Nauti and Mini Triton Coils. There are also videos on the Rebuildable Decks as well. Not thrilled with any of the videos. But they did give me a reference point for starting. Then adapting the techniques for personal use.

As far as ignoring people here, I don't live on the forum. There is a life out there. And you have to admit, this thread is just about dead, in regards ot any type of useful info for quite some time now. The only time I see any real activity, it is either to put some member in their place, or completely off topic. YMMV

Knife

Can I be added to the List Too!!!

 

[Knifemaker]

Can I be added to the List Too!!!

Azz Row Smurf, you've never been off it!

 

[AstroTurf]

Azz Row Smurf, you've never been off it!

L I K E ! ! !

 

[gnees]

L I K E ! ! !

Hi AT!!!!!!!

From the other post........

 

[AstroTurf]

Hi AT!!!!!!!

From the other post........

View attachment 582917

Oh My!!!

 

[BreSha6869]

I just ignore everyone and talk to myself. Less stressful.

 

[coldgin96]

Ticktock...

 

[FACE MEAT]

There were some hints from Mike a while back regarding a collaboration with ProVape. Are there any updates?