Atmistique Atomizers

[floridaBMW]

I def appreciate the help also. I plan to rebuild per ur suggestion. I actually did last night and slid maybe 3 into the slot. They sort of went 1 on top of the other. No resistance and it seems to be wicking good. Out of habit I have been primer puffing. Gonna hit it all day today without doing so. Thank You!


Sent from my iPhone using Tapatalk

 

[Konstantinos]

Pls keep us inform. This setup is kind different

 

[floridaBMW]

Will do, I should have taken pics. Thank you again.


Sent from my iPhone using Tapatalk

 

[Nach]

I usually vape with cisco and empire 306 without a problem.
What kind of 306 you use now?

"It's like sucking a golfball through a garden hose!" ))))))))))))))))))))))))

I had picked up some Joye 306's in bulk and they suck!!

EDIT: I just realized that I posted in the wrong thread too. Sorry!!


Sent from my iPad mini using Tapatalk

 

[Kataphraktos]

I def appreciate the help also. I plan to rebuild per ur suggestion. I actually did last night and slid maybe 3 into the slot. They sort of went 1 on top of the other. No resistance and it seems to be wicking good. Out of habit I have been primer puffing. Gonna hit it all day today without doing so. Thank You!


Sent from my iPhone using Tapatalk

As long as they don't feel like they are squeezing into the slots, 3 stacked one on top of the other should work fine. But they should twist so that they are laying side by side as they reach down to the slots, else they are much to "high" as a vertical stack and will get choked by the tube, if not outright sliced off by the tube when you try to screw it on.

 

[doctadrea]

Hey all, just thought I'd throw a shout out. I got my first diver working exactly as I want it to. I did a 2.5ohm coil above the cup. 4 1mm bamboo yarns, and left them frayed at the end and just long enough to not get into the threading. I vape 100% VG, but it's been feeding like a dream. I'm a few tanks in and it's just great. No fiddling, it just works every time. I'm in love, so thank you.

 

[qorax]

Konstantinos and my Greek Friends,

Here's Wishing You All A HAPPY
**GREEK INDEPENDENCE DAY**



From Canada!
March 25th, 2014

 

[crazyarms]

I am loving my diver v2. I tried the build with the coil above the cup and it is working like a charm. I was quite frustrated at first when I got it but after a few more builds it is working phenomenally. Leaks a little bit when filling my tank but other than that its flawless. Works well with my 100% VG juice as well as my thinner juices as well. And I finally got the build down so I can fix it up in a matter of minutes. I think i need another one!

 

[Konstantinos]

Q: i was surprised thanks a lot my friend

Crazy: what tank you use?

 

[crazyarms]

I am using the SnP by Vapour Art. Looks great and the fit was perfect. Only issue is a slight flooding when filling but that may have something to do with my wick setup.

 

[StrikeIII]

I am using the SnP by Vapour Art. Looks great and the fit was perfect. Only issue is a slight flooding when filling but that may have something to do with my wick setup.

With the diver it's still recommended that you still push the SnP tank up enough to cover the juice slots when filling or you'll get a little flooding when filling through the fill holes. Maybe when the SnP V2 is released it might be better since the fill holes will be larger to allow air to be pushed out faster.

Sent from my Galaxy Note 3 using Tapatalk 4

 

[crazyarms]

That makes sense. I usually pull the entire top piece off and remove the O rings when I fill which seems to help a bit, but not much. Makes sense though, those fill holes are tiny! I had to go buy a bunch of needle tip bottles just to fill it.

With the diver it's still recommended that you still push the SnP tank up enough to cover the juice slots when filling or you'll get a little flooding when filling through the fill holes. Maybe when the SnP V2 is released it might be better since the fill holes will be larger to allow air to be pushed out faster.

Sent from my Galaxy Note 3 using Tapatalk 4

 

[Konstantinos]

When filling the SnP follow these steps and you will be leak free:

1) Use carto tool and slide the Diver out just enough so the Diver juice hole is outside of the SnP
2) Open fill port on SnP
3) Fill to about 70% capacity
4) Close fill port on SnP
5) Slide Diver back into the SnP

 

[qorax]

Q: i was surprised thanks a lot my friend

Crazy: what tank you use?

Oh, I'm no more a frequent visitor to this thread b'coz both my Diver v2s work so well. I think that's a good thing

Love Atmistique for making this happen!

 

[Konstantinos]

I just surprised that you know our national holiday

 

[Kataphraktos]

I just surprised that you know our national holiday

I'm surprised Greece hasn't sold all its national holidays to the Nazis Germans.

 

[qorax]

I just surprised that you know our national holiday

We all celebrate it here. Canadians appreciate the contribution of Greeks in our society. And we love and respect everyone in the Globe.

Sea of blue and white: Toronto's Greek Independence Day parade kicks off | CTV Toronto News

Statement — Minister Kenney issues statement recognizing Greek Independence Day

https://www.liberal.ca/newsroom/new...leader-justin-trudeau-greek-independence-day/

Chow, Ford & Tory walk in Greek Independence Day parade | CityNews

 

[mikeulon]

Konstantinos! You sir, I hear are responsible for discovering the BB tank ball valve leak messing up all my builds. Scotch tape over the ball fixed my vape! I would kiss you but that would just be weird.

 

[Konstantinos]

A bit of )))

Dont put tape on it, just always be sure that the ball return to right position after you fill the tank

 

[Kataphraktos]

A bit of )))

Dont put tape on it, just always be sure that the ball return to right position after you fill the tank

Sometimes it is not enough, for those with this issue. My tank does not have this issue. A bit of tape provides the required seal, and you can just peel it back to refill through the port, then reapply.