You know what is funny they all leak a little condensation between part #3 and #4 but the authentic leaks the worst. Go figure.
- Status
@dwcraig1 I really want to thank you for showing me how to order Orings from the Oring store. I went there and had no idea of which type to get or how to find the correct ones. You saved me about $50 in parts.
Yeah I don't own a caliper, I think that is what they are called and I haven't tried interchanging parts but if there are difference they aren't visible to the naked eye.
I just got the kayfun v5 from tobecco, i had problems with the screws how they came stock, wondering if anyone else has this problem? sorry if its been asked before
They do say that some parts could be made of different metal then SS. All I know is they have the same quality of vape.
I have heard that before but I think it was solved by using authentic screws. I really have no problem because I use a single wire SS316L coil 26awg and they worked just fine. I have heard on some of these clones don't remember which one but the holes were not deep enough for the longer screws that are included with the SM spares kits. I just haven't had a reason to try.
Actually, we could be talking about two different things, but on the review i watched i think the screws are not meant to go down all the way. I think they leave a good bit of hanging room to trap huge wire like claptons or something, which normally the small kayfun screws would have trouble doing.
Regardless, i think i mightve found a solution to my problem. someone suggested heating it up and then freezing it.. wish me luck
The longer, spare screws i mean. the stock screws should screw down normally
I just can't believe they would do a fine job of machining, there are some places that look a little rough but not visible unless you take it apart. The threads are fine and all 4 of mine were almost as clean as the real thing. And the standard screws do go all the way down. They were on pretty tight when I first receive them but other then them being a little wiggley they tighten down well on the Tobeco.
Tobeco usually make pretty nice clones. The only ones I have heard by some are the EH Pro which hasn't come out with one yet.
Wow! The master at work! Thanks!It comes to $4.20 plus shipping for 10 of each size from theoringstore.
I guess my snip didn't get all of it's self in there.
The rest
Here: 1.0mm CS : The O-Ring Store LLC, We make getting O-Rings easy!
And here: 1.5mm CS : The O-Ring Store LLC, We make getting O-Rings easy!
I suggest putting some 12 x 1 mm in your order as well.
Example: 10 x 1 mm is 10 mm ID and 1 mm cross section.
Here's the one from 3f that someone had posted. It's 3ml capacity & also 62mm in height.
SXK Kayfun V5 Mini Kayfun 5 Mini Style RTA 22mm 316SS Silver Atomizer
I almost couldn't get mine loose. After that, one of them wouldn't screw down enough to hold my 28g wire without a lot of muscle because the hole wasn't threaded far enough down. The spare screws were worse. I ended up using a Dremel to shorten a screw until I received the the authentic spare parts kit and switched out the screws, using a short screw for the side that was not threaded all the way. Hope that makes sense.
I have one Tobeco that is letting too much juice in even at 1 full turn. Do you think #10 or #11 would cause that?
Possible 11, 10 would be more of outside leak. When I replaced #11 with an 11 the vape changed a bit, I put it in Escribe and sure enough the temp had came up.
Well Maybe I'll try that tomorrow. I can get by with it the rest of the day when the wick gets too wet I close it down some like maybe 1/2 to 3/4 turn and it eventually gets kind of anemic and just open it another 1/4 turn for a while. Maybe it's just me or the flavor I have in that one.
- Status
Similar threads
- Locked
