Yeah its the best RTA but I can opened AFC ring sir, just pull down with nail and it just like hurricane jr airflow it has stopper to prevetnt spining around. Watch closely it may have O Ring out jump out from a place so its a little h hard to pull out. Mine just like that so I change the o ring on AFC ring and plug in carefully and now it very smooth.
Augvape Merlin Mini By Roxy
- Thread starter MMW
- Start date
- th_trl_thread_readers 0
- Status
Augvape Merlin MINI, VIDEO review by Danial of djlsbvapes.com. What I learned:
NO press fit parts on the mini.
AFC ring can be pulled off but it's held on by orings and as seen in video review, can pinch them when pressed back on, so be CAREFUL, if you decide you want to clean under the AFC ring.
I'm hoping a US vendor will eventually sell the new BLACK version, I'm done with cheapo Chinese sites.
NO press fit parts on the mini.
AFC ring can be pulled off but it's held on by orings and as seen in video review, can pinch them when pressed back on, so be CAREFUL, if you decide you want to clean under the AFC ring.
I'm hoping a US vendor will eventually sell the new BLACK version, I'm done with cheapo Chinese sites.
Cons:
1. No improvement at all for its top fill mechanism.
2. JFC doesn't really close, it won't shut the juice from entering the chamber.
3. Very bad QC particularly with the o-ring originally placed on the tank.
4. Single coil deck now no more using Velocity type of post.
The biggest improvement is its "no more press fit" base. Since my 4ml Merlin is working fine, I rather buy the short tank parts that converts my 4ml tank to 2ml tank (from FT) than this one.
1. No improvement at all for its top fill mechanism.
2. JFC doesn't really close, it won't shut the juice from entering the chamber.
3. Very bad QC particularly with the o-ring originally placed on the tank.
4. Single coil deck now no more using Velocity type of post.
The biggest improvement is its "no more press fit" base. Since my 4ml Merlin is working fine, I rather buy the short tank parts that converts my 4ml tank to 2ml tank (from FT) than this one.
Let me address in numerical order. Not sure how much I like the mini yet, however.
1. wrong, a couple improvements, one the fill slots are a fair bit larger, and the o-ring which is easily lost is no longer an issue.
2. mine does, tested with water, single coil deck only, haven't tried dual coil deck.
3. not sure what your talking about here mine has no flaws whatsoever, as a matter of fact I'm not sure how fit/finish/quality could be any better.
4. I don't see any benefit to a velocity style deck for single coil use. If there is one please mention it. Other then one side being high/low, which really doesn't matter.
My opinion press fit doesn't really matter on the Merlin, long as it is fit together properly. Certainly has not been an issue for me. I will say the simplified base of the mini as a whole is an improvement. Another benefit, Augvape could release different style decks, not so sure they will bother, but who knows.
I prefer the larger diameter base, however this also is a negative due to capacity. If they are smart they will release an extension with longer glass/top section, possibly Euro TPP laws was an influence with capacity.
It really does not vape better then the original Merlin, and it also seems to be more critical of wicking. I can build my original Merlin and toss just about any reasonable build in it, not so much with the Mini.
All that said I don't think I would recommend the Mini as an upgrade to the Merlin. The original Merlin is still my first pick for single coil.
I agree with your 4 point response, saved me the time!
1. Anyone who practically refill a Merlin tank on a regular basic knows how frustrating the top cap system is. I either wrap it with toilet paper before open or wash my hand after refill.
2. Watch the DJLSB video, I can see the openning after JFC is closed.
3. You are lucky. Augvape should have at least a minimum concern on o-ring quality.
4. You obviously don't build coil very often or does not matter how your coil is being plugged to the posts. I do. Velocity deck is easier for coil building.
Discarding the press-fit mechanism of the base is a big matter to me, particularly when I need to clean the base thoroughly or to replace a o-ring therein. Don't you clean your Merlin regularly?
I really wish Augvape will improve the top fill mechnism, give us something more user-friendly.
Really, I find it simple, not frustrating at all, and use my Merlins every day, literally takes me a few seconds to fill. Think I've filled the little 8, or 9 times so far today. I would agree to this point if you said "some people", or "I", but anyone? I guess if it is such a bother there are other choices.
Why should I watch him? I have my own sitting right here.
Average quality China o-rings, guess that is what all those web stores who sell o-rings are for. But quite honestly other then the small o-ring in the top cap of my original Merlin which went down the drain I haven't needed a replacement.
LOL, Yea I have a butler that builds for my 400 or so atomizers.
Velocity deck is not the end all be all in electronic connections. Not even sure it would be my first choice, I'd have to ponder that. Again, in a single coil build 2 holes are plenty, but then we are just getting into opinion.Like many other atomizers a thorough cleaning doesn't have to rely on 100% take down, just ask all the people who use atomizers which are much more difficult/impossible to access the internals for cleaning. Granted it is more convenient and faster if it comes apart, but not a deal breaker if it doesn't.
Personally don't feel a need, I guess Augvape and Roxy felt the same way. Sure there are easier methods, and it is a consideration when I buy, its just a ways down on my list.
Why not just buy something else? Trying to convince people that already own it of all the Merlin Mini's so-called "cons" just does not make a whole lot of sense. That's one thing that is so great about vaping, you can always find something that works for you.
I am using the single coil deck and I do have to say/agree that this mini (for me) was finicky with the wicking. I spent some time of trial and error to get the wicking down for my build, after that it was all good. 
Ya, simple and dirty. Definitely frustrating me not you.
I prefer easy and clean, I think we are from 2 different worlds.
You lied.
I am sorry, I never expect "dirty" could be pleasing to someone like you. Yes I will take back the word "anyone" and replace it with "everyone except you".
So that you won't rush into buying something blindly.
I couldn't imagine how can one clean his tank near a drain, man... that is dirty, I always do my tank cleaning in my room.
I do spend a lot of time with 1 hole doing something else, but for attaching my vape coil to the post, 2 holes is the minimum number defintely not "plenty".
But it is the easist way to wash and make sure everything is cleaned up. Don't you like thing to be easier? Um.. you don't.
Did I?
What makes Augvape improve the base of this tank by replacing the press-fit mechanism with something easier to open?
It is the user's comment! The CONS of this tank must be raised!
In my opinion, the best way to kill a product is to praise it in every aspect with a brianless loyalty.
Btw, there is no proof that everyone visits this thread have already owned this tank. There are many people, e.g. me, always visit forums to read other's opinion before buying a tank.
Ok, enough negative "cons" from those that don't even own one or have not personally vaped a Merlin Mini. As most of you know there has yet to be made or sold, a perfect RTA. I posted my opinion and a few points, but it's probably scrolled by, so in short I find it much improved, and I like the mini over my 3 full sized versions due to the improvements, I'm certainly not going to debate with folks that don't own one, that's childish.
The info below is for those that like the product, and may be interested in a black version, as I am. I'll be getting at least two more. So.........
I wrote SubtankSupply, that's where I have bought my ORIGINAL Merlins, and my one SS Merlin Mini. Some of you from the Merlin full size thread may remember the owner replacing the first batch bases with improved ones at no charge. Mine was sent to me promptly as well. He had to spend his own time going through all of the bases he had and the ones coming in needed to be inspected. I was impressed with the above and beyond customer service and to show my appreciation, have bought all my Merlins as well as some other tanks from him.
In the email I sent him, I included the "Fastech" link for this "black mini", and asked if he had plans to sell them. After his response, I asked and received his permission to paste them here for our thread members.
QUOTE:
"I have had many ask and i asked the factory. the fast tech listing is just to get people to order.. they do not sell to fast tech.. i wont use the words the owner of augvape used but he said f@ck fast tech. then he said we will be doing a black but it is gonna be a while.. as soon as they tell me there ready to take my order i will have a pre order on the site for it.. but he said it will be a while.. they are still trying to fill there stainless orders.. thanks alot.
They (FastTech) will be selling a clone if they do have it,, that is what the factory owner told me last night. they let me know as soon as they have a product.. i will be the first to list it and have it in the usa."
I trust his response, and for the fair price he sells them for I can wait for a "black" ORIGINAL!
I freaking love this mini and already have my second on the way. Dont get me wrong I love my Merlin full sizes also (I have 2 of those also) I know vaping is subjective so your entitled to your opinion @hiclass however i disagree with just about everything you said concerning this awesome little performer
- Status
