Building a "hana" style mod with the fasttech enclosure: looking for tips, tricks, and suggestions
- Thread starter HOPS
- Start date
- th_trl_thread_readers 0
- Status
dougward1960, BlueFlyingV, and anyone else that is interested, I posted the new DNA40 cradle on shapeways.com. If you'd like to be a beta tester, please PM me.
How hard is it to make a 3d shape like that with tinker - thinking about coming up with something to use in a tube mod (really depends on what switches I use). Probably have to make it in two parts (each a half moon) so i can make the solder connections then slide it into the tube (adding switch caps afterwards).
polarbare, I only use SkecthUp, so I couldn't say how tinker would be. I do have a 19mm ID tube cradle on shapeways.com, but at the moment it's in beta and meant for the DNA30 & DNA20 ONLY.
If you let me know the inner diameter of your tube, I can create a DNA40 tube cradle for you
polarbare, I only use SkecthUp, so I couldn't say how tinker would be. I do have a 19mm ID tube cradle on shapeways.com, but at the moment it's in beta and meant for the DNA30 & DNA20 ONLY.
If you let me know the inner diameter of your tube, I can create a DNA40 tube cradle for you
I'll definitely let you know if I decide to go that route. Right now still finishing up this dna 40 box mod - want to see how it vapes and whether I like it enough to go thru the pain of making a tube mod
If you like programming, you could try OpenSCAD - The Programmers Solid 3D CAD Modeller or OpenJSCAD.org (webgl and javascript based)
For those of you that were waiting for me to release my USB charger cradle for sale on shapeways.com. It is now open for sale.
Thank you for being so patient while I've test-fitted, adjusted, and uploaded the new file to make it just right
@ polarbare, just for fun I've created a 19mm ID DNA40 cradle and posted it on shapeways.com. PM if you'd like to beta test it
Thank you for being so patient while I've test-fitted, adjusted, and uploaded the new file to make it just right
@ polarbare, just for fun I've created a 19mm ID DNA40 cradle and posted it on shapeways.com. PM if you'd like to beta test it
Thanks sanjosse, ordered a couple of them. Will let you know how everything turns out!
sanjosse still havent received my items yet, but i was curious about the adjustments you did to the charger. What do i need to do? Plus i got the hana cradle for DNA 30 but i want to use it for the DNA 40. Do i just snip off the lower part?
I didn't read the whole thread, so sorry for just jumping in. But I had a quick question about the fasttech enclosures. Has anyone been able to make a dual 18650 unregulated mod out of one yet? Not sure if some cutting inside would open it up enough to fit two battery sleds in there.
:: sent from android with tapatalk ::
:: sent from android with tapatalk ::
I think that will be very very tight. Mabye 5-7mm left above the battery case if you mill away stuff from the top and use a very compact one. You might need to use a non adjustable 510 and not sure where you would even fit a button.
I'd rather spend time and energy on making a kind of revolver magazine for the batteries!
I'd rather spend time and energy on making a kind of revolver magazine for the batteries!
Aal_, and for anyone else that purchased a USB Charger cradle beta unit. I made the following changes shown in the image below. The updated cradle can be found here on shapeways.com.
Regarding your DNA30 cradle question, the answer is yes, remove the single nub on the end opposite the curved end.
I just finished my first build, used a DNA40. I've got some kind of gremlin in the output leads or in the 510 itself--atomizers are reading 0.2-03 Ohms higher than they should. Has anyone had this type of problem before? This is all new to me and I can't really figure out how to troubleshoot it.
Any state side vendors have these boxes yet? Just checking before I make an order for a few.
Thanks
Thanks
Elev8 was selling off broken defective units for cheep But there out of stock now
DNA 30 ENCLOSURES *Read Description* - Elev8 Vape
DNA 30 ENCLOSURES *Read Description* - Elev8 Vape
They've been out of stock for at least a month. I ended up ordering a hana clone from FC and eventually replace the board with a DNA 40. They have a black one on a group buy for $37.90 and it ends in 6 days.
Focalecig -Best E-Cigarettes - Worldwide Free Shipping
Not sure if their code works with the group buy but use : fcvapingcheap for 10% off.
Aal_, The image is of the revised cradle, and yes, these minor tweaks should be done for the beta cradle to work correctly. I was able to modify mine in about 15 minutes
- Status
Similar threads
