Catfish Atty Mods the next Chapter

[Yiorgo]

I'm finding I have to time my sqounk.... I look at it with the top off and get a feel for where I want it to fully saturate and how long and hard of a sqounk it needs before it hits the side afc..... as I'm only rocking the side afc.... (if they leak it's my fault) side afc until I get my VECTOR .....!

All Your atty's fill and drain very well..... so ya just have to get used to it..... Or get used to carrying a paper towel with ya. Lol.


Sent from my SGH-M919 using Tapatalk

 

[hildicat]

So I guess I missed the boat on another cam-m? If these turn out to be as good as I hope, I sure hope you do another run. Was already contemplating getting on the list for another...

Since I'm currently working from my phone, could one of you kind people please add my name to the bottom of the list? Figure I might get lucky and score two if you have any dropouts.

 

[rudedog]

I cant wait for the CAM-M,been messin with this pva40 and the TP stuff just don't do it for a mech head like me.but im not gonna sell it for 80$.it also can thump someones skull if ya have the need.its a heavy beach for sure.MECH'S RULE!!imho anyways

 

[Nautilusfan]

18650 CAM Mech Squonker
1. 73neb
2. Graywolf1911
3. Houndb
4. Magaro
5. hildicat
6. Nautilusfan
7. Papa_Lazarou
8. Lutses
9. Magnetnerd
10. TheDigital99

Backup

11. yinsen
12. snakedoc
13. Robbieblood
14. IonMan
15. distortoblotto
16. petemoss
17. B2L
18. Raynman
19. 2buildawall
20. JeffreyAce
21. Rex Everything
22. Chadshaw
23. Loopy 1224
24. spacelord
25. cd68
26 Subohmies
27. pwheeler
28. calpis
29. bullhcr
30. Slappy3139
31. kiloyst
32. Havok333
33. rudedog
34. Walter Ego
35. Daigoman
36. SeanMoore
37. Clark F
38. Raynman
39. Kentastic
40. Asbestos4004
41. supersport13
42. EZinTN
43. Houndb
44. Wolfenstark
45. marshallb
46. saku808
47. Hildicat

 

[Nautilusfan]

So I guess I missed the boat on another cam-m? If these turn out to be as good as I hope, I sure hope you do another run. Was already contemplating getting on the list for another...

Since I'm currently working from my phone, could one of you kind people please add my name to the bottom of the list? Figure I might get lucky and score two if you have any dropouts.

There you go

 

[Subohmies]

Hastur arrived today
Got to say it is the best top afc rda
Amazing cloud and flavor
Love how the afc works

 

[hildicat]

There you go

Thanks!

 

[Chowderhead1972]

Hastur arrived today
Got to say it is the best top afc rda
Amazing cloud and flavor
Love how the afc works

But the million dollar questions: will it accept a regular drip tip? What is the thread pitch of the center pin? M2.5 or M3. How about a 45 degree deck shot? I'm warming up to it with a m3 center pin this could be a crowd pleaser. Let me get pic of the contact pin removed and one of the deck focusing on where the positive post meets the deck.

 

[jeffreyace]

What is requiet to clean your contacts? Nolax? Or small amount of sanding?

 

[Big Hitter]

Hello Catfish fans and customers. Per Tom's request I am posting my questions here to aid me in loving squonking again.

Been bottom feeding almost 100% since November 2010 until recently .... now it just hasn't been doing it for me.

I'm sure the problem is my atomizers available. All I have is 3 original Chalice attys ...... no other BF attys and no dripping attys at all.

Taking over my daily vape has been the Squape R ..... I have 3 of them and run them all on the 3.1 mm air hole. I build pretty high for that large of hole 1.2 to 1.4 ohms. I don't do quick lung hits I still take long slow 6-8 second drags. Even though the air hole is pretty large I don't suck all the air I can through it as fast as possible.

I love flavor, vapor I don't care how much I make as long as it tastes good and has throat it.

Still use 10-12 mg juice

I'm looking for an atty for my LP Grand that I can get 3.1mm equivalent and still build over an ohm single coil.

I might do duals once and a while but I'm lazy and single coils work great for me in my Squape

Tom suggested a derringer for a start ...... what do you all think.

Anyone else vape around 1.3 with 12mg nice slow easy hits ??

 

[Chowderhead1972]

Welcome to Catfish Big hitter!

 

[Asbestos4004]

Hello Catfish fans and customers. Per Tom's request I am posting my questions here to aid me in loving squonking again.

Been bottom feeding almost 100% since November 2010 until recently .... now it just hasn't been doing it for me.

I'm sure the problem is my atomizers available. All I have is 3 original Chalice attys ...... no other BF attys and no dripping attys at all.

Taking over my daily vape has been the Squape R ..... I have 3 of them and run them all on the 3.1 mm air hole. I build pretty high for that large of hole 1.2 to 1.4 ohms. I don't do quick lung hits I still take long slow 6-8 second drags. Even though the air hole is pretty large I don't suck all the air I can through it as fast as possible.

I love flavor, vapor I don't care how much I make as long as it tastes good and has throat it.

Still use 10-12 mg juice

I'm looking for an atty for my LP Grand that I can get 3.1mm equivalent and still build over an ohm single coil.

I might do duals once and a while but I'm lazy and single coils work great for me in my Squape

Tom suggested a derringer for a start ...... what do you all think.

Anyone else vape around 1.3 with 12mg nice slow easy hits ??

I'd agree, the Derringer is a great place to start. Maybe a Rogue. Better yet,if he has any left, get a stumpy! Ah hell....if it's a CAM atty, you can't really go wrong! Welcome!

 

[Asbestos4004]

What is requiet to clean your contacts? Nolax? Or small amount of sanding?

Contacts on what? No sandpaper on REO contacts, please. Try a white pencil eraser before sanding anything, regardless of the mod. Then Noalox, or Deoxit.

 

[Chowderhead1972]

What is requiet to clean your contacts? Nolax? Or small amount of sanding?

Over the long term maybe some 600-1200 grit wet dry sand paper but a simple disassembly (4 nylon screws) and a wipe down and polish with a paper towel would cover most of it. Long term the fine grit sandpaper would be helpful with any build up. If you build low you will know when it needs cleaning and you will know when it's right. I hit mine with a little red de-oxit and it hit HARD.... I need to find brass m5 grub screws 10-15mm long, these will be the negative bond at the bottom of the mod, no juice contact. The box as I received it comes with stainless grubs but they are a bit hard on the batteries. All of the other materials I have. I need to order a few more 10ml needle bottles as well, I only have 100 right now.

 

[puffon]

But the million dollar questions: will it accept a regular drip tip? What is the thread pitch of the center pin? M2.5 or M3. How about a 45 degree deck shot? I'm warming up to it with a m3 center pin this could be a crowd pleaser. Let me get pic of the contact pin removed and one of the deck focusing on where the positive post meets the deck.

You should know soon.
Mine is scheduled for delivery to you, today or tomorrow.

 

[Asbestos4004]

Over the long term maybe some 600-1200 grit wet dry sand paper but a simple disassembly (4 nylon screws) and a wipe down and polish with a paper towel would cover most of it. Long term the fine grit sandpaper would be helpful with any build up. If you build low you will know when it needs cleaning and you will know when it's right. I hit mine with a little red de-oxit and it hit HARD.... I need to find brass m5 grub screws 10-15mm long, these will be the negative bond at the bottom of the mod, no juice contact. The box as I received it comes with stainless grubs but they are a bit hard on the batteries. All of the other materials I have. I need to order a few more 10ml needle bottles as well, I only have 100 right now.

ooooooohhhhhh, THAT mod........ belt sander.

 

[Chowderhead1972]

Contacts on what? No sandpaper on REO contacts, please. Try a white pencil eraser before sanding anything, regardless of the mod. Then Noalox, or Deoxit.

The CAM-M is not a Reo by any stretch. No plated contacts. This baby will dump all 50 available amps at the push of a button.

Just thinking out loud I wonder how Tarn-X would work? Anyone tried it?

 

[Chowderhead1972]

You should know soon.
Mine is scheduled for delivery to you, today or tomorrow.

Sweet! Let me get that link again. I was trying to take a break from attys for a minute but if this is awesome.....

 

[Asbestos4004]

The CAM-M is not a Reo by any stretch. No plated contacts. This baby will dump all 50 available amps at the push of a button.

Just thinking out loud I wonder how Tarn-X would work? Anyone tried it?

I have......If you can clean it THOROUGHLY after Tarn X, maybe. It leaves a bit of a film.

 

[Subohmies]

Not sure what the size of the center pin
But i hack the factory pin out and fitted aromamizer bf pin with no issue.
The aromamizer pin was about 3.6mm tho. And it does came with a 510 adapter.

On the left was the provided 510 adapter and the factory center pin in the right

I will take a photo of the deck with the pin removed when i have a chance[emoji6]

This might help