e-smokeguru official thread

[chefski]

I see the single pieces for ithaka update are available but not in full.. if i purchase all single pieces will that build the update?

 

[jjkanto]

Lucky I had ESG email notification! Thought only Tilemahos spares were dropping today!

 

[chefski]

I have a full cart. Just waiting to buy until I'm a sure about the update for ithaka. .

 

[thodouris]

I feel more than lucky today,just finished 2 tubes and got a ggts
Thank you uncle Bill!!

 

[chefski]

Does anyone hknow the pieces needed for a complete update for ithaka?

 

[Martino.]

Ok Just another ss mix Brass carried away

 

[RandomFellow]

Did anyone else have problems logging in with their user accounts? The site kept telling me incorrect username/password, so I had to check out as guest. Perhaps it was because I was using safari on my iPhone. Just curious if anyone else had this issue.

 

[RandomFellow]

Does anyone hknow the pieces needed for a complete update for ithaka?

Oh god, there are so many. And not all of them are available today. I too am waiting on a full rebuildable part, and thought about trying to buy all the individual pieces. The parts are:
Negative post
Positive post
2 screws
Plastic sandwich
Negative post platform
Positive post platform
Little plastic washer
Little plastic thread cover
AD post
AD screw
O-ring
Cup
Mouthpiece

 

[RandomFellow]

Ithaka steel window eludes me again :-( got everything else I wanted though! Brass accessories for my JustGG

Same here. I don't think I will ever own this part. :-(

 

[chefski]

Thank you so much. If it's not all available i shall wait for the full update!! Time to check out.

 

[RandomFellow]

Basically, if you go to the Ithaka Accessories section, everything listed after the Full Update part is what you need (1 of everything except the screws, which you need 2), except that you only need either the full mouthpiece or the drip tip mouthpiece.

 

[chefski]

So everything is available to build the update?

 

[chefski]

Sorry. Just checked. Not everything is in stock..

 

[chefski]

Basically, if you go to the Ithaka Accessories section, everything listed after the Full Update part is what you need (1 of everything except the screws, which you need 2), except that you only need either the full mouthpiece or the drip tip mouthpiece.

Your information is very helpful and I thank you!

 

[Aal_]

I feel more than lucky today,just finished 2 tubes and got a ggts
Thank you uncle Bill!!

Thodouris you are late on the ggts. It is old school now

 

[Aal_]

Forgot abou the sale today. I wanted an esterigon button brass pin. Was it ever in stock?

 

[thodouris]

Thodouris you are late on the ggts. It is old school now

i know it,
its my first ts
but i promise that it will be safe inside the bubble wrap

 

[chefski]

Almost got everything I needed. Missed out on the just gg top lid and pin.. I hope the ithaka update will be available in the future. And very excited about the hybrid piece!

 

[Ariel_MX]

These are the parts required to build a complete Ithaka Update Kit:

-From left to right-
(some components are mounted)

1 x Mouthpiece for Ithaka update
1 x Center Post for Ithaka update*
1 x Penelope V3 / Ithaka Update /Tilemahos Positive Pin*
1 x Penelope V3 / Ithaka Update Sandwich Plastic
1 x Penelope V3 / Ithaka Update Insulator
1 x Penelope V3 / Ithaka Update Negative Base*
1 x Penelope V3 / Ithaka Update / Tilemahos Negative Pin*
1 x Housing for Ithaka update
1 x O-Ring 14mm x 1mm (around housing)*
1 x Penelope V3 / Ithaka Update Center Post Plastic
1 x Center Post Pin (Brass) for Ithaka update
1 x O-Ring (2mm thick, 8mm outside diameter, 3.5mm internal diameter)
1 x Penelope V2 / V3 / Ithaka Update AD Pin

2 x Penelope V3 / Ithaka Update / Tilemahos Wire Holder*

*Mounted on picture

Out of stock (at the time of this post):

Penelope V2 / V3 / Ithaka Update AD Pin
Penelope V3 / Ithaka Update Negative Base
Penelope V3 / Ithaka Update Insulator

 

[chefski]

These are the parts required to build a complete Ithaka Update Kit:

-From left to right-
(some components are mounted)

1 x Mouthpiece for Ithaka update
1 x Center Post for Ithaka update*
1 x Penelope V3 / Ithaka Update /Tilemahos Positive Pin*
1 x Penelope V3 / Ithaka Update Sandwich Plastic
1 x Penelope V3 / Ithaka Update Insulator
1 x Penelope V3 / Ithaka Update Negative Base*
1 x Penelope V3 / Ithaka Update / Tilemahos Negative Pin*
1 x Housing for Ithaka update
1 x Penelope V3 / Ithaka Update Center Post Plastic
1 x Center Post Pin (Brass) for Ithaka update
1 x O-Ring (2mm thick, 8mm outside diameter, 3.5mm internal diameter)
1 x Penelope V2 / V3 / Ithaka Update AD Pin

2 x Penelope V3 / Ithaka Update / Tilemahos Wire Holder*

*Mounted on picture

Out of stock (at the time of this post):

Penelope V2 / V3 / Ithaka Update AD Pin
Penelope V3 / Ithaka Update Negative Base
Penelope V3 / Ithaka Update Insulator

Thank you so much. I'm going to wait until I can purchase a complete one. Your help is greatly appreciated!