what air hole screw? there isn't one on mine, just the air hole and filler screw on the bottom(air hole on the side of the base, no screw)
EHPRO Kayfun Lite Clone
- Thread starter thomasjames0
- Start date
- th_trl_thread_readers 0
- Status
what air hole screw? there isn't one on mine, just the air hole and filler screw on the bottom(air hole on the side of the base, no screw)
I haven't seen this mentioned in this thread, but it appears as if EHPro designed this to have the legs of the coil go through the holes under the screws? This is the way I have mine built now, with the wick stuffed down into the chamber, it doesn't produce a hot leg, but I do notice it when I dry burn it.
sorry I kinda dont know how to describe it, its the centerpost screw i think, its a long tube that screws into the positive terminal, I took it out and there was plastic gunk in it
Here's a build I posted in the KFL thread
My first attempt at a dual coil. Tried it on my ehpro clone.
12 wraps of 27g on 1/16 bit for each coil. I used the side holes on the deck to mount them
Each coil has 3 strands cotton yarn as a wick.
Came out to .6ohm
Made sure the tails are against the deck wall and he channels are completely visible.
Sent from my iPhone using Tapatalk 2
Sent from my iPhone using Tapatalk 2
My first attempt at a dual coil. Tried it on my ehpro clone.
12 wraps of 27g on 1/16 bit for each coil. I used the side holes on the deck to mount them
Each coil has 3 strands cotton yarn as a wick.
Came out to .6ohm
Made sure the tails are against the deck wall and he channels are completely visible.
Sent from my iPhone using Tapatalk 2
Sent from my iPhone using Tapatalk 2
Here's a build I posted in the KFL thread
My first attempt at a dual coil. Tried it on my ehpro clone.
12 wraps of 27g on 1/16 bit for each coil. I used the side holes on the deck to mount them
Each coil has 3 strands cotton yarn as a wick.
Came out to .6ohm
Made sure the tails are against the deck wall and he channels are completely visible.
Sent from my iPhone using Tapatalk 2
Sent from my iPhone using Tapatalk 2
that looks nice, but it would be better if they had the right screws so you could capture the wire under the screwhead.....
I have no problem capturing a single coil build under the stock screws, done it a bunch.
I'm sure a dual coil is possible too but I didn't really care to give it a shot
Sent from my HTC One using Tapatalk
what drip tips have you guys used? i can only use the factory tip as none of mine fit (not even the o-ring, the base or bottom of the tip just doesn't fit). also how deep do you drill the hole in the center post? do you need to take that plastic thingie out? the draw is just way too tight for me
i have been to three hardware stores in my area and have yet to find the appropriate machine screws
i haven't been able to find any stainless steel m1.6 screws. i give up man, going to have to order 100 pack online lol
Last edited:
i hate the draw on this thing. i want to drill out the holes, but i dont know what to do about those plastic pieces in the base. also the hole in the base on the outside (the inlet) is at an angle and i dont know what to do
do the screws have to be stainless steel? I have found zinc screws for 35cents- does anybody know if they will work?
I've shopped around on a couple of sites and the price for the screw itself is cheap but shipping is going to be a ......
$5 for 2 screws hell no.
$5 for 2 screws hell no.
@peterforpats i didn't want zinc because it's supposed to be really bad for you, so i only looked for ss.
side note: my clone is dead. i was very disatisfied with the draw. i tried drilling out larger than 1/16 - went to 5/64 and ended up drilling the threads out (in the center hole that the coil sits over). while the kayfun produces great flavor, i really, really dislike the draw. it is just too tight for me. I guess there's no point in getting another one for myself, but im still learning, only been vaping for a few months
side note: my clone is dead. i was very disatisfied with the draw. i tried drilling out larger than 1/16 - went to 5/64 and ended up drilling the threads out (in the center hole that the coil sits over). while the kayfun produces great flavor, i really, really dislike the draw. it is just too tight for me. I guess there's no point in getting another one for myself, but im still learning, only been vaping for a few months
VapeToy has them in stock. I couldn't find screws either had to cut mine down.
- Status
Similar threads
