ERA - easy rebuildable atomzier

[Mudflap]

Got my ERA today. My first coil is 6 wraps @ 2.3Ω. I'm running it at 4.6 volts under load on the VV Grand. It vapes very nice!

That's a confused and lonely Joye 510 SR atty standing in front.

 

[MXBNW]

Nice set up. I got one on my Grand at 1.2 and it Rocks. Next I will set one up for the VVG.

Got my ERA today. My first coil is 6 wraps @ 2.3Ω. I'm running it at 4.6 volts under load on the VV Grand. It vapes very nice!

That's a confused and lonely Joye 510 SR atty standing in front.

 

[MXBNW]

Hay Mud looks like you got the right wire in the bottom hole?

The bottom hole is where the juice comes out. I may not be seeing it right. Eyes are getting old and its been a long day.

 

[Mudflap]

Hay Mud looks like you got the right wire in the bottom hole?

The bottom hole is where the juice comes out. I may not be seeing it right. Eyes are getting old and its been a long day.

Yeah, I figured that out after the fact and moved it to the top hole. LOL

 

[urquidezj]

Here it is! Bottom feed setup like Tey Gajitos from the phillipines does.
What u need
-I'm using 30 g kanthal to get the lr I want and the surface area I need for good vape to soak ratio
-Six era cap lengths of wick
-torch
-wire cutters
-tweezers (not pictured)
-era
-reo (lol)

Get your wick fold it in half nice and even then fold it again. Keeping it nice and even. Get your kanthal, whatever gauge you are using and wrap to desired resistance. I did four of 30g wich will land me in the 1.4 neighborhood

Torch your wick and wire before mounting

Mount coil n wick onto era. Make sure u use the top holes and juice feed is right below your coil. While you hold wick in place with your thumb tighten the grub screw with Allen wrench. This needs attention, do not over tighten as it will cut your wires on both sides, snug it and tighten a bit till you see your wire tails slightly move up

Spread your coil out nice and even

Trim or twist off excess wire

With the remaining wire tail or if you don't have a long enough one make a u

Now we hook the loop edges of the wick together one side first then hook the other to bring them together on the opposing side of your coil

Now hold down with thumb and start twisting the u together. Use needle nose Pliers or tweezers to get a nice tight twist and cut off excess

Cut off remaining tails of wick

Should look like this

Test on reo or other devise multimeter

Once om your reo make sure your air hole is directly in from of your coil. This is crucial if you want it to perform like its supposed to

Squonk with you cap off so you can get an idea how much you need to squonk whenever you are dry. Fire it a couple of times to see vapor produced. After that. Vape your face off!!!!!
http://i50.photobucket.com/albums/f...-B979-337CED13FDAF-16766-00000D6AD024C5ED.mp4
As you can see in the vid. It blows clouds. The draw in it is perfect just how I like it, loose, hope this helps any questions feel free to ask, credits on the wick setup go to Tey Gajitos.
Oh yeah 50/50 bluemist vaping caramel tobacco with an aw 18650 batt.

 

[MXBNW]

urquidezj: Got mine set up almost the same way with a few less wraps Mine came out at 1.2 using IMR 18650 It Vapes like no other atty I have had on my Grand. Loving mine.

Nice step by step by the way.

BTW: I can not get the vid to work

 

[doubledown]

Got my ERA today. My first coil is 6 wraps @ 2.3Ω. I'm running it at 4.6 volts under load on the VV Grand. It vapes very nice!

That's a confused and lonely Joye 510 SR atty standing in front.

Mudflap, how the *#}# did you get a polished vv grand!?! Uh yeah, I'm jealous Rooooooooooooobbbb!!!

 

[urquidezj]

urquidezj: Got mine set up almost the same way with a few less wraps Mine came out at 1.2 using IMR 18650 It Vapes like no other atty I have had on my Grand. Loving mine.

Nice step by step by the way.

BTW: I can not get the vid to work

it is a lil beast. vid worked fine for me bro just clicked it and it opens window on g chrome

 

[MXBNW]

I will try again.

Just check the ERA on the Grand 1.2 at 3.7v+ is 12+ Watts WOW Now I know why I am loving my Grand again

it is a lil beast. vid worked fine for me bro just clicked it and it opens window on g chrome

 

[urquidezj]

i wanna stack two 16340s lol at 1.2 ohms, dam! i suck at math lol 30 some watts lol

 

[MXBNW]

Ok two (2) 16340's is 3.2v each = 7.20V at 1.2 Ohms its 43.2 Watts

Not sure your wire would last more then about 2 Seconds LOL but sure would put off a glow

i wanna stack two 16340s lol at 1.2 ohms, dam! i suck at math lol 30 some watts lol

 

[Neimad]

Hello,

Can somebody say me if they make the ERA work on the Reo Mini finally ?
I think I understand the ERA do not fit in the Juice cup, but the pin is much longer and can make contact.
Is it possible to push the tube above the bottle in order to put the center pin more higher in the Reo ?

 

[Mudflap]

Hello,

Can somebody say me if they make the ERA work on the Reo Mini finally ?
I think I understand the ERA do not fit in the Juice cup, but the pin is much longer and can make contact.
Is it possible to push the tube above the bottle in order to put the center pin more higher in the Reo ?

This is what Alice came up with to use her ERA's on her Reo Mini Woodvil. I don't see why it wouldn't work on a metal Reo Mini or any of the other Woodvils either. Way to go, Alice.

All you need is one unsealed 510 - 510 adapter to raise the connection so the ERA will fit and make contact and one eGo shorty cone to slip over the adapter for a finished appearance. (vendor links provided are for illustration. adapters and eGo cones can be bought from dozens of different vendors)

 

[par292]

thats what im doing is using a unsealed 510-510 adaptor on mine, and it works just fine

 

[Neimad]

Yes, it's an elegant solution
Sure I prefer do not use an adapter, but if I have no choice, I'll try this one

 

[doubledown]

Hey, I like that. I'd looked up the 510 adapters but the shorty cone makes a nice finished application. Simple solutions like this are one of the things that makes vaping continue to be so much fun. I can't remember the last time I saw an elegant adapter solution on an analog

 

[colt45]

ok folks, how important is it to torch your wick and coil before use and if it really is where do i find a small torch like in these pics. i dont wanna get a big tank type torch

 

[FeistyAlice]

Here it is! Bottom feed setup like Tey Gajitos from the phillipines does.
What u need
-I'm using 30 g kanthal to get the lr I want and the surface area I need for good vape to soak ratio
-Six era cap lengths of wick
-torch
-wire cutters
-tweezers (not pictured)
-era
-reo (lol)

Get your wick fold it in half nice and even then fold it again. Keeping it nice and even. Get your kanthal, whatever gauge you are using and wrap to desired resistance. I did four of 30g wich will land me in the 1.4 neighborhood

Torch your wick and wire before mounting

Mount coil n wick onto era. Make sure u use the top holes and juice feed is right below your coil. While you hold wick in place with your thumb tighten the grub screw with Allen wrench. This needs attention, do not over tighten as it will cut your wires on both sides, snug it and tighten a bit till you see your wire tails slightly move up

Spread your coil out nice and even

Trim or twist off excess wire

With the remaining wire tail or if you don't have a long enough one make a u

Now we hook the loop edges of the wick together one side first then hook the other to bring them together on the opposing side of your coil

Now hold down with thumb and start twisting the u together. Use needle nose Pliers or tweezers to get a nice tight twist and cut off excess

Cut off remaining tails of wick

Should look like this

Test on reo or other devise multimeter

Once om your reo make sure your air hole is directly in from of your coil. This is crucial if you want it to perform like its supposed to

Squonk with you cap off so you can get an idea how much you need to squonk whenever you are dry. Fire it a couple of times to see vapor produced. After that. Vape your face off!!!!!
http://i50.photobucket.com/albums/f...-B979-337CED13FDAF-16766-00000D6AD024C5ED.mp4
As you can see in the vid. It blows clouds. The draw in it is perfect just how I like it, loose, hope this helps any questions feel free to ask, credits on the wick setup go to Tey Gajitos.
Oh yeah 50/50 bluemist vaping caramel tobacco with an aw 18650 batt.

Great Tutorial!!!! Thanks.

 

[colt45]

also could someone post how many wraps to get 1.5 and 2.0 ohms
i use 32 awg kanthal a1

 

[FeistyAlice]

ok folks, how important is it to torch your wick and coil before use and if it really is where do i find a small torch like in these pics. i dont wanna get a big tank type torch

I'm not sure torching is really needed. After I made the coiled wick I soaked in PGA for any hour and then blotted dry, then put on ERA. No bad taste and I'm really sensitive to anything that alters the taste. I did put some juice on it and did a few short dry burns first. It only took a few for the coil to turn black.

Feisty Alice