Fogger V4!!

[Tbev]

Where'd you get it?

 

[Atrain009]

I see...... If the screws stuck hold post w pliers and try to get it out maby put it in the freezer for 20 minutes then go. Or use lube in the threads.

Sent from my Transformer TF101 using Tapatalk

Hmmm, I'll try the freezer trick.

Where'd you get it?

Eciggity

 

[AMDTrucking]

Hey, has this happened to anyone? I just received my fogger about 15 minutes ago, but Ive already run into a problem. One of the screws works fine, but the negative screw seems to be stuck in it's post. So when I try to unscrew it, it comes out from the bottom instead of the top like it should - the whole post comes out.

View attachment 352405

As you can see in the picture, the screw in the positive post comes out, but the screw in the negative post stays in it while the post itself is unscrewed.

I've tried remove the whole post, holding it with pliers, and trying to unscrew the screw out, but to no avail.

Any ideas on how to fix this?

I guess you already know what I would have done:
I would remove the post and put it in the vise. Then I would try to unscrew the stuck screw even if I had to heat the post with the torch. And, in case if the screw breaks (very likely that it will) I, then will drill it out with 1.5 mm drill bit and re-thread the hole to M1.6 x 0.35 mm.

 

[Tbev]

I'd get a refund send that pos back and buy one from eBay

 

[snowsnee]

The difference between 4.3 and 4.4 is the deck and the chimney is the (smaller 4.4 chimney) better over a larger chimney and deck version 4.3 ? Or is it just preference ? Better vape with what chimney ?

 

[BNEAT]

The difference between 4.3 and 4.4 is the deck and the chimney is the (smaller 4.4 chimney) better over a larger chimney and deck version 4.3 ? Or is it just preference ? Better vape with what chimney ?

4.3 is a pain in the arss, and it doesn't hold nearly enough juice! 4.4 is much easier to fill, much more juice capacity, and the vape is a little better with the smaller chamber (hardly noticible, really)

edit: the only thing "better" about the 4.3 is that the larger build deck makes it a little easier to build/wick, but they're both a little tricky at first.

 

[350ZMO]

Any ideas on how to fix this?

You could leave it off. What I have done now is remove the ground post and screw completely, go into the parts bag and get the extra fill port screw and put that in where the ground post was - makes it great for the ground leg on a dual vertical coil build which I prefer over the horizontal.

 

[gandsr]

Fogger 4.3, big deck. No leaks, no dry hits, great flavor, no cloud, fog, vape whatever you want to call it. I get more cloud, fog, vape from my Kayfuns and Taifuns! I'm using 28 gage kanthal and rayon. I use a 2 mm bit to build. Im running at 1.0 ohm. I thought this was the Kayfun killer. Not so far. My AGA T7 is the atty to beat. No leaks, no dry hits, fantastic flavor. Exact same bulild coil wise as the Fogger.
What am I doing wrong?

 

[brianc11111]

maybe nothing......i know im vaping my aga t7 more than my fogger

 

[Tbev]

Blah... Using too much wick, drop it down to 0.70hm

 

[brianc11111]

haha blah....aga t7 is a mighty fine atty

 

[Nailz]

I was curious about the aga t7, then lost interest really fast, only 1.5mil capacity

Been using the new fogger v4.1 (4.4) for a few nights at work, and I am loving this fogger, I've not measured it, but know it holds a good amount of juice, can use it all night at work and still have plenty of juice left in the tank, even with running dual coils at 0.5ohms. The vapor and flavor is better than my kayfuns, can see another fogger in my hands in the near future

 

[brianc11111]

I was curious about the aga t7, then lost interest really fast, only 1.5mil capacity

Been using the new fogger v4.1 (4.4) for a few nights at work, and I am loving this fogger, I've not measured it, but know it holds a good amount of juice, can use it all night at work and still have plenty of juice left in the tank, even with running dual coils at 0.5ohms. The vapor and flavor is better than my kayfuns, can see another fogger in my hands in the near future

the glass is 1.5....it holds about 4mil

 

[AMDTrucking]

^ What he said. 4 ML

 

[lsutiger]

Got my 4.4 in today and I am soking it right now to clean it. I wick my 4.3 with cotton, with very little and fanning it near the juice channels - none in the channel, and it vapes incredibly! Would I wick this the same way or would I put some in the channels, because of the L shape?

 

[Nailz]

Well according to Youde it is 1.5mils

 

[Nailz]

Got my 4.4 in today and I am soking it right now to clean it. I wick my 4.3 with cotton, with very little and fanning it near the juice channels - none in the channel, and it vapes incredibly! Would I wick this the same way or would I put some in the channels, because of the L shape?

Mine I cut my wick level with the chimney and then lightly pushed it down on to the deck, and so far it has been working great, no dry hits and no leaking.

 

[ewspears]

Why are we talking about T7's on a fogger thread????

 

[AMDTrucking]

Why are we talking about T7's on a fogger thread????

Because we love them all

 

[SPBALLER]

Just got my fogger v4(.4) today, and I'm blown away. This thing rocks!!!!

Not nearly as hard to build/wick as I thought it was going to be (maybe thats just beginners luck). The taste is as good as my kayfuns, the vapor is better, it holds as much juice, the airflow control is incredible, you really notice the differences where as my KFL+ v2 airflow control is a joke (authentic KFL too), you really have two options, screw in to where it doesn't mar your mod sitting flush, or screw out, and I don't notice a whole lot of difference in either. You can truly fine tune your vape with the foggers AFC.

I love my kayfuns (have 3), and maybe its just because its my first day with the fogger and I haven't had any issues yet, but right now my nod goes to the fogger v4.4. I'm beyond impressed and will be getting a few more of these ASAP!