homemade atomizer bottom feed
- Thread starter Cry79
- Start date
- th_trl_thread_readers 0
- Status
I bought some of it here
1x silver multi-adapters for e-cigarette - E-cigarette adapters Heaven Gifts
but a year ago
EDIT
from the image they seem to be the same
but it is better to look for them in the U.S.
if not cost you too much for shipping
1x silver multi-adapters for e-cigarette - E-cigarette adapters Heaven Gifts
but a year ago
EDIT
from the image they seem to be the same
but it is better to look for them in the U.S.
if not cost you too much for shipping
Last edited:
Thanks Cry, That is a good starting point. I did order a few more from another vendor but need to look at them before I post where I ordered.
Thanks This is a big help.
Thanks This is a big help.
Looking forward to seeing your Vid.
I need to order NR wire as well.
I need to order NR wire as well.
Anyway, I'm just waiting for the Phoenix
then I do a video step by step, to complete all
scubabatdan posted a link to NR wire cheap at twistedjewels.com. 0.999 Fine silver 30 gauge round for 50 cents/ft
I have ordered modding connectors from HG, and they took over a month to deliver. They are a good vendor but don't believe them on shipping times. I ordered 3 different things from china at the same time and they all got here before the connectors.
I have ordered modding connectors from HG, and they took over a month to deliver. They are a good vendor but don't believe them on shipping times. I ordered 3 different things from china at the same time and they all got here before the connectors.
Last edited:
I have some .999 fine silver wire but, I like this this nickel wire a little better.
Last edited:
30ga. I use it in a Penelope. It's stiffer than the silver but, you won't bend it and break it either.
Anyway, I'm just waiting for the Phoenix
then I do a video step by step, to complete all
Terrific! Thanks cry! I am curious how it vapes.
-Sam
One thing I have been thinking, how will the airflow hit the coil? It doesn't seem with the stock hole it would hit the coil dead on
-Sam
-Sam
Got this is today and its perfect.
eGo-510 connector - Use eGo Mega atty and tank on your mod!
center pin screws in, and its unsealed to feed juice. Was able to open up the center pin so the tube of the CE3 can be pres fit nicely. This worked great with the CE3's stock coil and wick. In lieu of the proper o-ring I used some electrical tape to secure the neg wire. The only problem was the coil was 2.8Ω, so I ripped it out and made a new coil for it. Since I don't have the capacity to solder, I tried to use the tape for both the neg and pos. wires. I got it to fire, but honestly this was a mess and wouldn't hold up long term.
So, Cry, could you please find out the size o-rings you used for both the pos. wire and the larger one for the neg wire. Other than that, if anyone has any recommendations for securing the two wires without having to solder that would be awesome.
Oh, the Phoenix cap fits perfectly, but on my setup at least, the coil is quite close to the top, leaving the air hole in the cap below the cup and coil, Might have to seal that one and drill a new on closer to the coil.
eGo-510 connector - Use eGo Mega atty and tank on your mod!
center pin screws in, and its unsealed to feed juice. Was able to open up the center pin so the tube of the CE3 can be pres fit nicely. This worked great with the CE3's stock coil and wick. In lieu of the proper o-ring I used some electrical tape to secure the neg wire. The only problem was the coil was 2.8Ω, so I ripped it out and made a new coil for it. Since I don't have the capacity to solder, I tried to use the tape for both the neg and pos. wires. I got it to fire, but honestly this was a mess and wouldn't hold up long term.
So, Cry, could you please find out the size o-rings you used for both the pos. wire and the larger one for the neg wire. Other than that, if anyone has any recommendations for securing the two wires without having to solder that would be awesome.
Oh, the Phoenix cap fits perfectly, but on my setup at least, the coil is quite close to the top, leaving the air hole in the cap below the cup and coil, Might have to seal that one and drill a new on closer to the coil.
It must something to do with heating up the Copper, as there are Copper water lines ?
Actually I have seen it indicated that it's unsafe but, I haven't seen any real evidence of that. I think it's really that it effects the taste of the juice.
I wouldn't think that would be the issue--people have cooked with copper pots and tea kettles for hundreds of years. I assumed it was because of some chemical reaction.
What elements? Will you be storing yours outside?
@ cry
Very, very nice and the no soldering assembly is sweet and elegant.
And for those who feel a ceramic atty cup adds to the experience the down tube could be blocked, and a side hole top cap could be used to make it a dripper.
- Status
Similar threads
