Finally was able to get the email to work on my cell phone
Here is the picture of the tank, where the stoppers ARE flush:
Hugs,
Skeeterkck
- Status
Finally was able to get the email to work on my cell phone
Here is the picture of the tank, where the stoppers ARE flush:Hugs,
Skeeterkck
Just keep the mouth piece on the cart and use a piece of paper towel soaked in your goof-off or nail polish remover and wrap it around the cart. Let it soak for a couple of minutes and it will all wipe off. After that just dry it off and then use rubbing alcohol to remove the nasty smell and glue residue. It should be good to go. That what I did until my stickerless carts came in.
Finally was able to get the email to work on my cell phone
View attachment 56894
Hugs,
Skeeterkck
That looks like it would work to me. I usually put my plunger things in the other way, but there's no reason it has to be that way (as far as I know).
Skeeter- I don't really know. Can you post a picture?
This saddle piercing doo-hicky is AW-SUM! I got one at home depot today. It's not that fancy type from the aquarium type stores, but it works fine. I'm using the syringe plunger as a sort of a jig to get the holes in the right place like this...
I put the plunger (with the hole already in it) on the carto where I want it to eventually be, then I move it down so that it's hanging off the bottom of the carto by about 1/2 it's width. Then I use that to line up the carto in the piercer. I punch the carto, and before I take it out, I use a pencil to lightly mark the syringe plunger 180 degrees from where the first hole is. I loosen the puncher part and the two tightening screws, then rotate the carto 180 so that my pencil mark is now up at the top. I tighten the screws and then punch again. I'm doing ~4 full turns past where I first hear the spike pierce the metal. That puts two holes on opposite sides right down at the bottom where I will need them to be when the tank is assembled.
ETA: a picture, in case that didn't make any sense.
Ahh, thanks for the pic, now I understand. Good idea.
On my mods, I have the 2 rib plungers and I have the second ribs just outside the tank. See Photo
Attachments
Last edited:
That is what mine DOESN'T do
Hugs,
Skeeterkck
Flip the plungers over? Or not... I don't think it matters. As long as it's an air tight seal it should work.
I did, it is STILL flush either way It doesn't have the overlap lip on these plungers Gonna super glue the plunger on the bottom side
Hugs,
Skeeterkck
It doesn't have the overlap lip on these plungers Gonna super glue the plunger on the bottom side Hugs,
Skeeterkck
Last edited:
Be back later tonight after midnite Will experiment more then
Hugs,
Skeeterkck
Thanks a million all, I appreciate it
Will experiment more then Hugs,
Skeeterkck
Thanks a million all, I appreciate it
Crystal Clear Vaping has the boge cartos in stainless now. So much easier than trying to get the glue off.
Thanks. I've been waiting for them to get in the Resurectors, course I'll have to de-sticker them. Just looked again, still out, but one of the options is SS, so maybe won't have to de sticker.
The teflon tape has been tried for other modifications and when the e-juice got on it-it disintegrated. Can't be good for us. I am enjoying this thread and playing around with making tanks.
I used a washcloth.with my finger nail ..it really worked..took about 3 min for a clean carto.
I guess I did a stupid thing...I've used my black cartos not realizing it was a sticker...I've got six tanks made and vaping with the black still on the carto....
Good to know. I know they use it on water supplies all the time so that surprises me that ejuice would disintegrate. I will do a experiment with laying a piece in Ejuice and letting it sit and see what happens.
How has it been holding up with the sticker. I know E-Juice wont take the glue off after you remove the sticker so who knows it might be great without removing it. The sticker is like a vinyl paper so I don't think that would hurt anything either. I may have to try one with the wrapper on it.
There are some that are painted, I have some 808's that are that way.
If the hole in the plunger is bigger than the carto and you want to fill it,try cutting a piece of the carto condom and put it on the carto.
I haven't tried this as my plungers are tight on the carto's,it should work,no teflon tape needed.
Or make the slit/hole in the carto lower to hide inside the plunger end,then it acts as a well to use every drop of your precious e-liquid of choice
I haven't tried this as my plungers are tight on the carto's,it should work,no teflon tape needed.
Or make the slit/hole in the carto lower to hide inside the plunger end,then it acts as a well to use every drop of your precious e-liquid of choice
Last edited:
- Status
