NP! Because if you're making holsters for Zenesi, I might have to switch from, errr, another supplier.
- Status
NP! Because if you're making holsters for Zenesi, I might have to switch from, errr, another supplier.
clip or belt loop style...??
I personally prefer clip, because I don't wear belts!clip or belt loop style...??
Hi ecitek,
My Mini has not been shipped yet, so I haven't tryied and experimented with it, but I do own some Genesis atomizers and some of them have a similar design to the attomizer part of the Zenesis. I was having the same liquid flooding the combustion chamber problem with one of them (The Line), it was not a design problem or defect on it, the flooding was due the top cap was not tight enough to the atty body, the effect was a pool of liquid inside the combustion chamber, and the liquid level on the tank decreased significantly.
I think there was some kind of siphon effect inside the combustion chamber, causing flood in it.
You could try putting an O-ring between the top cap and the body for testing purposes, we do not want to damage the tank over tightening the top cap.
Just an idea
the top cap isn't threaded the o ring is already there. there can't be a syphoning effect cause of the fill/air hole in the tank.
IF YOU HAVE ISSUES WITH THE STANDARD SWITCH AND YOU ARE USING AW IMR 18650s.
I have about 40 magnets that will help. I will mail one to you free of charge tomorrow. It will take the wobble out of the switch. This is my fix, and it has worked perfectly since I added the magnet.
If you want one, hit me up. I have to figure a way to ship them. I have to put them on something metal or they won't make it through the mail sorter. These are STRONG little magnets. I'll make it work.
If you are having trouble with your switch, I feel for you. I was, too. This will work for the 1600 mah AW IMR. I don't know abou the 2000.
It's first-come, first served. PM me to get one.
I have about 40 magnets that will help. I will mail one to you free of charge tomorrow. It will take the wobble out of the switch. This is my fix, and it has worked perfectly since I added the magnet.
If you want one, hit me up. I have to figure a way to ship them. I have to put them on something metal or they won't make it through the mail sorter. These are STRONG little magnets. I'll make it work.
If you are having trouble with your switch, I feel for you. I was, too. This will work for the 1600 mah AW IMR. I don't know abou the 2000.
It's first-come, first served. PM me to get one.
A early WELCOME to TN. We here youngin's enjoy new plp's. No mud slingin' just some good ol' honky tonkin'. Hope your move will be a happy one. Upper Middle TN here about 45 min east of Clarksville.
They work on the 2000 too! I was frustrated that my switch was so wobbly I couldn't set my Standard upright on my desk. So I took out the spacer and put a small neodymium magnet on top of the screw so it would be able to make contact with the battery - problem solved!
LOL, when you're that close you're a Kentennian. I spent my teenage yrs living on the state line on Hwy 31W my folks still live there.
Are the people having issues with liquid pooling in the top cap nostril exhalers?
I like to toot a little out and take a second/third drag and noticed this caused all kinds of issues with top cap juice on other genesis atties.
I like to toot a little out and take a second/third drag and noticed this caused all kinds of issues with top cap juice on other genesis atties.
Nope.
I just made a new wick and coil. It went well and I made the wick cinched off at the top like Zen~ does it. It also is a little more snug in the wick hole. Not tight, just a little push and it goes in. I initially had issues with the the top wrap creating a hotspot, but kept firing it a little at a time, then nudged it with a finger nail. Hotspot gone, and it is firing great and wicking better then my last wick. However, I cannot lay it on its side. I guess the fill hole allows liquid to flow out the wick or vice versa and it filled the top cap after my new fill up. My Line V1 doesn't have this fill hole in the top (the V2 will) and can be laid on its side without leaking no problem and it vapes fine if I use a straw style wick. So I plugged my fill hole with a toothpick and it can be laid on its side without leaking and It still vapes fine using 80/20 pg/vg. I vape a lot on the couch and like to lay my PV on the couch, so a cartomizer .... plug will find a new use... cause I am plugging the hole knowing that I can get it to vape just fine without it and can open the wick top back to a straw style if need be.
Mine may not have shown up yesterday like it was suppose to (Thanks Post office) but I did get to check out and take JollyRogers Mini for a test drive yesterday. I'm difinitely looking fwd to getting home tomorrow for sure!
thats funny cause so can I about 1/8 mile away from main gate Ft Campbell..
- Status
Similar threads
- Locked
