im not a big fan of the appearance of the sliding door. looks outdated to me, but im willing to overlook that if its a solid performer
IPV4 preorder
- Thread starter dangaranga
- Start date
- th_trl_thread_readers 0
- Status
Couldn't disagree more. I think the Sig 150, and even the ipv3 look outdated. At least the ipv4 is more than just a {MODERATED} box.
Last edited by a moderator:
It has kind of a firearm / large rifle clip appearance to me... which i am not a huge fan of...
you can see peoples eyes dart when pull out my IPV3 with a black tugboat2 on it as it is...
maybe I'll get some florescent pink drip tips to put people at ease
but hey no screws on this case !! yay!!
you can see peoples eyes dart when pull out my IPV3 with a black tugboat2 on it as it is...
maybe I'll get some florescent pink drip tips to put people at ease
but hey no screws on this case !! yay!!
Last edited:
Since I'm getting mine so damn cheap I'll probably splurge and throw a jwrap on it. If they offer alternate sleeves, that would be cool.
I'm sure. You can put wraps on a vapor shark and that's pretty rubbery
Then it may end up being a good looking mod. And it's not cheap SPV, you're just an thrifty buyer
I have to IPV 30W and 50W and they have both been very good to me.
I have to IPV 30W and 50W and they have both been very good to me.
Last edited:
Then it may end up being a good looking mod. And it's not cheap SPV, you're just an thrifty buyer
I have to IPV 30W and 50W and they have both been very good to me.
Well, 62 bucks is cheap for me. lol.
I got it from the same place i beat the round 3 cutoff luckily.
did you make it in round 1 or 2?
did you make it in round 1 or 2?
I got in on round 2 when there were still 43 left. I think it took less than a day for all those to go. Where else would you get a dual battery mod for 62 and change. Cheap even if it wasn't TP.
HD
Well appearances aside, I put in my order for a black version and ordered a fresh set of 25r's to feed her. And i already sold off my Ipv mini v2, so im stuck with my homebrewed parallel 18650 un-reg box till it shows up.
Any recommended vendors other than LV for the nickel wire? they seem to be out of 28awg ni200. I'll keep an eye out just incase they get some back in stock
Any recommended vendors other than LV for the nickel wire? they seem to be out of 28awg ni200. I'll keep an eye out just incase they get some back in stock
i got mine from amazon shipped with prime
Genuine AtomizerWick Brand Pure Nickel Wire 28 Gauge - non resistance AWG Ni200 - 100ft, 50ft and 25ft Available!!! - - Amazon.com
Genuine AtomizerWick Brand Pure Nickel Wire 28 Gauge - non resistance AWG Ni200 - 100ft, 50ft and 25ft Available!!! - - Amazon.com
EBay, from a vendor called atomizer n wick (spelling might be wrong). Have ordered from them quite a few times. They have thousands of feedback with a 100% favorable rating. Really fast shipping as well.
HD
Round 2. I snagged one right after the temp control news broke.
Must be the same people as I got mine from on eBay. I checked the spelling this time. The seller is atomizer.wick. 50 feet for $7.25 with free shipping. Over 10,000 feedback replies and a 100% favorable rating.
HD
So are they shipping with temp control or is it an upgrade once received. And your right SPV, $62 is extremely cheap. If it works as designed it could cause a real stir since that's right around the cost of the DNA40 chip.
Damn this industry moves fast!
- Status
Similar threads
