the eco glue can also stop that in its tracks if total safety is what your looking for.
- Status
yup the eco glue is amazing ...fixes leaks & cracks & actually holds up to e-juice . And if you want to remove it ...soak item in hot water & it will let go of item & you can peel it off & start over .
I got my latest order last night (Visions& Turbines). Thanks BAD !
I didn't even think to look for cracks. I am so secure in my crack fixing abilities ...
well that and BAD'S crack checking abilities .
The Turbines look pretty cool w/their little squishy bladder on the tank .
And the revised Visions seem to have several changes as well ....
can't wait to try 'em ...am fighting the urge to load 'em up .
I have 2 tank attys,2 maxomizers & a CE2 in rotation @the moment ...
so something needs to die 1st
I can only vape so many things at one time .
I am NOT a modder, but I like to push my clear cartos to last...even I can use the glue with ease
I am a messy person when I use it...but, it works well and easy to use.
True I guess. I would like to see a plug on the fluxo's to replace the fill plug. I always remove an replace upside down with great effect on wicking. I don't think the fill plug needs to be around the cup at all. Just so it seals the top. I like the idea of a vortex 1.0 style plug, or an extended top plug that makes it all the way to the cup. The only issue would be prefilled ones leaking while stored at a vendor or during shipping with that style plug. The plug needing to be pulled up or flipped upside down is the only thing I have to do with this generation of ce2's. So if they made this last modification I think they would be ready to go out of the box. It only takes 20 seconds to prep a new one though so it isn't an issue for me, but for newcomers to the ce2 it would save some trouble and confusion. Just my 2 cents.
Last edited:
Ya I always forget to grab some with my order. And then every time I get a crack I slap my forehead. I just replaced my first vision tube because after 4-5 days the crack in my first batch vision 2.0 (issue resolved on gotvapes end now) grew to a point where it was starting to leak. Replacement was easy enough although I had to scrap the rubber ring at the base because I couldn't get the tube on without pinching and damaging it. No leaking or anything even without it. So now it's been dry burned and back to 100%. I really can't say how impressed I am with the new Vision. For the first time ever I can let my ce2's take a break. Went out to the bar and never had to even think about refilling anything. Hurray!
yup just got the new test batch of vision deux's . Issue is resolved and back to the orginal packaging procedure.
Thanks everyone for bringing this to our attention so we could nip it in the bud as fast as we did.
you need to grease the silicone ring and the inside of the tube with juice so it slides over it easier.
Thanks everyone for bringing this to our attention so we could nip it in the bud as fast as we did.
you need to grease the silicone ring and the inside of the tube with juice so it slides over it easier.
This may never happen but any chance getting a vision cone for the epower? I've been using the vision on one and the diameter seems perfect for it. Just need a cone that will go up over half of the vision. Like the length of a normal epower cone just the right diameter to accept the vision. Don't know why but I really like how it fits the epower more than the ego. I could just grind down one of my epower cones and get a similar one to the ego vision cone, but I really want a longer cone to protect more and look sleeker. Dunno just something to think about.
Great to hear. Knew you guys were on it.
I know I can get the tube on there without scrapping the ring, it just happened not to work this time. Just throwing out my experience with the vision as I use it. Thanks
Don't know what others have seen but while dry buning the vision I noticed this company really knows how to wrap a coil! It's so precise and even. I'm used to the ce2 coils and the vision's looks like whatever process they use is much better. Don't know if this has an effect on performance or not but just thought it interesting.
I just got mine today, I ran them at 4 for a while and noticed if I didn't let it rest in between hits, it would start to dry up a little. Not sure what it'd do at 6... maybe I'll try it and report back later
I just got mine today, I ran them at 4 for a while and noticed if I didn't let it rest in between hits, it would start to dry up a little. Not sure what it'd do at 6... maybe I'll try it and report back later
I use the vision sometimes at 4.5ish volts on a 5v passthrough attatched to a usb battery pack. Not sure what the exact voltage is. If you pull the plug up a little bit so there is no space between the mouthpiece and plug, It takes care of any wicking issues at this voltage. I will venture a guess 6v will be much too much for the vision. 4.5v is about the highest I will go with it.
Yeah got to 5.5 volts and popped the coil. I never learn. Good thing I got 2. I'd sy 6v not a good ideaI just got mine today, I ran them at 4 for a while and noticed if I didn't let it rest in between hits, it would start to dry up a little. Not sure what it'd do at 6... maybe I'll try it and report back later
Hey everyone I just got my new Vision Deux yesterday and using it on and off since. It arrived in good condition with no cracks in the tube. The wicks inside looked a little wet with primer so I gave it a couple quick burns but no bad taste. So I loaded it up with some juice which is a 60PG/40VG and used it on my standard eGo battery for about an hour pretty steady.
I am getting pretty good cool vapor but very little flavor. At first I thought it must not be wicking very well but not noticing any dry or burnt taste. Just hardy any taste at all. I changed to another juice that is 70PG/30VG and it is still the same with hardy no flavor. It almost acting like not enough juice is making it's way up the wicks to the coil. Is that possible?
Do you think I need to raise the inside rubber piece? Could it be pressing down on the wicks too much?
Also I notice the vapor is cool, not warm and as I said I am using on a regular eGo 650mah battery. Is that normal for these with a top coil?
Any help or suggestions will be greatly appreciated.
Thanks
I am getting pretty good cool vapor but very little flavor. At first I thought it must not be wicking very well but not noticing any dry or burnt taste. Just hardy any taste at all. I changed to another juice that is 70PG/30VG and it is still the same with hardy no flavor. It almost acting like not enough juice is making it's way up the wicks to the coil. Is that possible?
Do you think I need to raise the inside rubber piece? Could it be pressing down on the wicks too much?
Also I notice the vapor is cool, not warm and as I said I am using on a regular eGo 650mah battery. Is that normal for these with a top coil?
Any help or suggestions will be greatly appreciated.
Thanks
If you are getting good vapor and no burnt taste it sounds like it is wicking fine. I believe the Vision's draw is adjustable by moving the sloted pin in the battery connector end clock-wise to tighten the draw a bit. Sometimes when there is too much air it will mute/reduce the flavor. The atty also may just need to brake in a bit before it starts giving you better flavor. IF you want a warmer vapor you can try it at 4.2-4.5 V.
I just got my 1 Vision V2 today but haven't bothered to try it out since I ordered 4 boxes of Saphires. Took one Saphire out of the box and filled it and it works perfectly!! The draw is much better than the 1st batch of these for 1 thing. Running it at 5.8 W on my Darwin which sends 3.7V to the atty. I am not going to push these above 3.7V as I don't want juice buring on the wick. There has been some changes/improvements on the latest batch of Saphires which likely will have solved the issues some people were having. I will make a post about this and my experience with the newest Saphire Friday as I want to use one for at least 24 hours. So far I am loving the Saphires even more than the 1st batch ones.
yes these where improved as i mentioned in the sapphire thread days ago and the new 3.0 ohm for HV vaping has been shipped.
glad your liking them
glad your liking them
Matt you may be right about the air flow being the issue as this one has a really airy draw on it right now. I will adjust the end to try to get a tighter draw and see if that helps.
I really like the design on these and the easy filling so I really hope I can get it working right because then it will be a winner.
I really like the design on these and the easy filling so I really hope I can get it working right because then it will be a winner.
- Status
Similar threads
- Locked
