I need one more week to finish the assembling Yankee. Then I will immediately ship to my sellers. As for your idea, is not bad at all. But maybe its good to reduce nic level if you have the opportunity
Ithaka official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
I need one more week to finish the assembling Yankee. Then I will immediately ship to my sellers. As for your idea, is not bad at all. But maybe its good to reduce nic level if you have the opportunity
Hi there Imeo ....Yankee
Close getting close
Found some time and Watched the vid looking good ..... Imeo I got a question ...how thick is the inner channel on ithaka ? Same as penny?
Always good to reduce nic level.
I was posting that for people that don't do their own juice. If they have, for example 12mg, and they are not ready to reduce yet, there is another way.
I was posting that for people that don't do their own juice. If they have, for example 12mg, and they are not ready to reduce yet, there is another way.
Hi there Imeo ....Yankee
Close getting close
Found some time and Watched the vid looking good ..... Imeo I got a question ...how thick is the inner channel on ithaka ? Same as penny?
Getting close indeed. Won't be close enough until its in my dirty little hands.
Always good to reduce nic level.
I was posting that for people that don't do their own juice. If they have, for example 12mg, and they are not ready to reduce yet, there is another way.
Pray tell. I use 18mg in my ody with 3.7v@1.0Ω. Been thinking about reducing my level, but I recently had a bit of a snafu with ordering and ended up with several hundred mls of this.
Pray tell. I use 18mg in my ody with 3.7v@1.0Ω. Been thinking about reducing my level, but I recently had a bit of a snafu with ordering and ended up with several hundred mls of this.
So in your setup, if you use dual coils, you'd end up around .5-.6 ohms. But if you make each wire 2ohms, and use dual coil setup, your overall res should fall at your liking of 1ohms. That gets you vaping where you want to be, and in the future, your order will be for lower nic.
Same as Ody Aron. 2mm depth and 2,5mm in width
Hi there Imeo ....Yankee
Close getting close
Found some time and Watched the vid looking good ..... Imeo I got a question ...how thick is the inner channel on ithaka ? Same as penny?
Ah, yes yankee, I agree
Always good to reduce nic level.
I was posting that for people that don't do their own juice. If they have, for example 12mg, and they are not ready to reduce yet, there is another way.
yeah the problem is when the brass oxidizes, you do not want that in contact with your juice, stainless all the way
someone mentioned 4 ithaka videos? are they all on this thread or are they somewhere else? i just figured id ask so i dont waste to much time combing threw threads. I saw the one at the beginning of thread, are the others on here as well? thanks all
Videos look awesome. So I was thinking more of the 3.5 mm silica wick for the ithaka. Sorry if this was mentioned before, but could we just do a single coil wrap, then gently separate the strands and put 3 strands of silica in each channel? Do you think this would work, such as being enough material in each channel and such?
3mm or 2,5mm are ok on channels Long. To my opinion, you can remove 2 strands from your 3,5mm wick so you get a 2,5mm wick. Then you put 2 wicks topically on coil
Right in this thread, a few pages back.
thanks yankee, i need to see more of ithaka so i can get ready to experiment when its arrives
One more configuration for the guys that dont want to make a X style with a coil around 2 wicks, is to make a diagonal coil and then put a wick without wire on the first one, diagonal again. Or make the opposite. Put first the non coiled wick and then the coiled wick, all diagonal.
I will let you find new tricks, no reason to ruin your fun
I will let you find new tricks, no reason to ruin your fun
I'm wondering Imeo, have you tried doing, or do you know how it would work out if we put 2 wicks in an X, but have the coil around both wicks.
So I imagine it would look like >///< if that makes sense? "///" is the coil, ">" and "<" are the wicks
Just trying to think of other setups
So I imagine it would look like >///< if that makes sense? "///" is the coil, ">" and "<" are the wicks
Just trying to think of other setups
Yeah I figured it would work pretty good and get lots of juice to the coils. Maybe even add a couple strands under the coil? Or would that be overkill? I like how you can adjust the rebuildable part so there is more room on the mouthpiece.. we'll be able to fit more wick/coil in there, not having to be completely all in the ceramic cup (that was an issue for me with Ody, if I ever wanted to have a bulky coil and wick, with 100% VG juice)
Someone correct me out there. When I put empty wick over the coil I feel less heat. When I put empty wick under the coil I feel less vapor since air does not hit coil directly. Does this make sense or am I just paranoid?
- Status
Similar threads
