Kayfun lite plus clone bottom pin
- Thread starter aje742
- Start date
- th_trl_thread_readers 0
- Status
The bottom pin does turn when screwed, but it does not move. I think it adjusts something near the posts.
EDIT: after some fiddling around, that does seem to work! I haven't looked inside so I don't know what's going on in there - hopefully nothing too bad.
Thanks!
EDIT: after some fiddling around, that does seem to work! I haven't looked inside so I don't know what's going on in there - hopefully nothing too bad.
Thanks!
Last edited:
The center pin is the screw that also holds the block on the deck for one of the contacts for the coil, so be careful when you adjust it. Especially if you have a coil on it. Also make sure it's not touching the other base for the other contact, make sure you can see a gap between them.
No one ever reads post about the same problems before posting again. Just linked someone yesterday.
Fatdaddyvapes Tobeco Kayfun Lite Plus Complete Overhaul Rebuild Kit | eBay
Fatdaddyvapes Tobeco Kayfun Lite Plus Complete Overhaul Rebuild Kit | eBay
Depending on the clone version you have, EHPro, HCigar or Tobeco (TOgether BEst COrporation), the bottom screw loosens the positive block on the EHPro and HCigar versions. The only version that has an adjustable bottom pin/screw is the Tobeco.
Which one do you have?
I'm not sure which one it is, it was purchased from electronicstix.
Could something like this be of use to "bridge the gap"?
510 - 510 Charging Adapter
Edit: Found that link in this thread: http://www.e-cigarette-forum.com/fo...scussion/150801-510-extension-does-exist.html
Could something like this be of use to "bridge the gap"?
510 - 510 Charging Adapter
Edit: Found that link in this thread: http://www.e-cigarette-forum.com/fo...scussion/150801-510-extension-does-exist.html
Last edited:
Please take a picture of the 510 threads from the side and post it to this thread so we can see how far in or out the center pin/screw is.
I don't see how that charging adapter would help if the center pin/screw is to far in.
Also the pin/screw would need to be recessed several millimeters, like 4-6, inside the 510 threads for it not to work on most APV's.
Your only option if it is recessed that far is to get a Delrin washer to place under the screw head to move it out. You should be able to get them at any fairly good local hardware store.
I don't see how that charging adapter would help if the center pin/screw is to far in.
Also the pin/screw would need to be recessed several millimeters, like 4-6, inside the 510 threads for it not to work on most APV's.
Your only option if it is recessed that far is to get a Delrin washer to place under the screw head to move it out. You should be able to get them at any fairly good local hardware store.
I had the same issue on my SID and Vamo and the fix was to replace the insulators on the MODs with Danco number 60 O-Rings. This raises up the center pin so it will make good contact with all my atomizers as well as fixing the dreaded 02 error on the Vamo.
The insulators had been showing signs that they needed to be replaced anyway.
The insulators had been showing signs that they needed to be replaced anyway.
Airflow Adapter
This looks like it could help, but I don't know if I want to buy from a store with so many spelling mistakes...
This looks like it could help, but I don't know if I want to buy from a store with so many spelling mistakes...
Went to a B&M and they gave me a Circuit Board Spacer and it seems to do the trick!
just so you know, its not just you. I got one local the other day, and had same problem. I called her up and the other one she had in stock was same way. she refunded it and is sending both back to company.
I bought a clone and have the same problem. I am able to use an air flow adapter I had laying around between the mod and the tank and that works fine. Looks crappy, but works.
Try a circuit board spacer from Madvapes. It will correct the issue. Definitely overpriced but handy.Circuit Board Spacer
You can find the same thing at your local hardware store for about 3-10 cents.
ian91:13416569 said:
How does this spacer work? Just drop it in the 510 connector of the MVP?
No you take the center screw out and put that spacer on it then reinsert it. It move the screw head, the slotted part, down so it make the connection to your battery mod.
All you need is a delrin, plastic, washer from your local hardware store. Any good hardware store, even a Lowes or Home Depot, has them.
I had mine open to rewick yesterday and tried a simple solution: I wrapped a little bit of dental floss around the pin, just under the head. About 3 wraps of the floss raised the head up a tiny bit, enough to solve the connection problem. Kind of a cheesy solution, but it worked.
- Status
Similar threads
