Cinnamon is the almighty God of tank killers..
Best of luck with your search for a M Tank.
Sent from my iPhone using Tapatalk 2
- Status
Cinnamon is the almighty God of tank killers..
Best of luck with your search for a M Tank.
Sent from my iPhone using Tapatalk 2
The difference is that the Protank has a threaded center tube, which captures the tank section between the base and the top cap. The Kayfun doesn't.
if a new threaded chimney and threaded top cap was made, then glass would be practical
If the chimney threaded into the top section, it'd be very much like a big Protank 2.
But you'd also want to change out the base (if going full glass) or metal tank sections (if going band of glass) to replace the unnecessary threads with o-rings. And suddenly you've pretty much redesigned the whole atomiser, perhaps having to change the dimensions as well to make sure the chimney and chimney / top section join was sturdy enough to hold the whole thing together.
KFL 2, SvoeMesto? Anyone speak Russian?
But aftermarket, I could see a glass / metal sleeve tank replacing the three tank sections. You'd just need the top and bottom metal sections to thread into each other, and the glass bit to be held in place inside with o-rings. Probably heavy, but its heavy enough already, so who cares.
Probably blooming expensive too, because not much demand...
(edit - I wonder if there'd be enough space for liquid then, unless you bulged out the tank. Maybe not so possible after all...?)
(edit again - but then if there were enough metal and very small windows, perhaps the glass could be made quite thin, and not need to bear any appreciable load?)
But you'd also want to change out the base (if going full glass) or metal tank sections (if going band of glass) to replace the unnecessary threads with o-rings. And suddenly you've pretty much redesigned the whole atomiser, perhaps having to change the dimensions as well to make sure the chimney and chimney / top section join was sturdy enough to hold the whole thing together.
KFL 2, SvoeMesto? Anyone speak Russian?
But aftermarket, I could see a glass / metal sleeve tank replacing the three tank sections. You'd just need the top and bottom metal sections to thread into each other, and the glass bit to be held in place inside with o-rings. Probably heavy, but its heavy enough already, so who cares.
Probably blooming expensive too, because not much demand...
(edit - I wonder if there'd be enough space for liquid then, unless you bulged out the tank. Maybe not so possible after all...?)
(edit again - but then if there were enough metal and very small windows, perhaps the glass could be made quite thin, and not need to bear any appreciable load?)
Last edited:
Cloud9 has them in stock right now. I'm currently stalking their site for the nano kit
Last edited:
good lookin out on the cloud9 reference. but it says its for the 3.1. will it fit the lite as well?
Intaste.de has them in stock, in colors, too. Intaste will back out the VAT at checkout since it will be shipping to the US. Cloud9 does not.
Sent from my iPad
Yeah, they are the same. I also found these guys selling a china made version for $10.
EDIT: their prices on everything else are ridiculous!
Last edited:
Cloud9 is in England, which is not in the European Union. England does not give any breaks to merchandise shipped outside of the country. Intaste is in Germany, part of the EU, and the EU does back it out.
Sent from my iPad
I've never bought this but maybe contact them and find out for sure if it's shorter.
Kayfun Short Ultra Tank
I just received a KFL+ from C9V and they didn't charge VAT. I placed another order for some extra bits today and they didn't charge it then either. I live in Canada.
That's because we still have "her" on our money.. you know, HRM The Queen*.
* I don't claim any of this to be fact. It should be though!
Once I select international - worldwide shipping, it adds the VAT. Must have something to do with Canada?
Haha - then someone should tell eCigz.uk that. They took a little polite persuading .....
We are in the EU, we just have a slightly distant relationship to it, having never joined the Eurozone.
(and no - not that anyone was going to ask - I don't have a clue about the VAT thing, sorry)
Last edited:
Yesterday I posted my latest KFL coil build using Kanthal ribbon, after a tankful I have to say the ribbon provides better flavor, TH and slightly more vapor than any of my 1.2ohm round Kanthal coils did, the ribbon build measured at 1.6 ohms and 1.5mm diameter.
Todays build is with the same Kanthal ribbon, the difference this time is the stacked dual coil the flavor the Aspire coils produce inspired me to try their same style stacked coil arrangement on the KFL this one measures out at 1.56 ohms, it's not the prettiest coil on the block but works great, and it's producing more vapor than the single coil ribbon flavor report by days end tomorrow.
Here's a look at it
Todays build is with the same Kanthal ribbon, the difference this time is the stacked dual coil the flavor the Aspire coils produce inspired me to try their same style stacked coil arrangement on the KFL this one measures out at 1.56 ohms, it's not the prettiest coil on the block but works great, and it's producing more vapor than the single coil ribbon flavor report by days end tomorrow.
Here's a look at it
Last edited:
I do have some ribbon left and been meaning to give it a go on the lite. I did like the vapor it was producing on my gennys but it was weird because there was hardly any TH compared to the round. I had it set up in the ac-9, maybe a 3 wrap which was like .6 or something, this was on a porous ceramic wick so just about everything was completely different compared to doing this in a kayfun, micro coil and cotton wick. I guess I just never really tried it because I was thinking about the TH issue. I know there have been good results with the ribbon wraps touching, they call it a tin man coil.
I always believe that a thicker wire will always produce a better flavor, whether it is 26g round or thicker or a wide ribbon wire. is that hemp fibers? love that stuff. since using the hemp, I rarely use cotton anymore. sorry maybe that is cotton and its just the color of your juice.Yesterday I posted my latest KFL coil build using Kanthal ribbon, after a tankful I have to say the ribbon provides better flavor, TH and slightly more vapor than any of my 1.2ohm round Kanthal coils did, the ribbon build measured at 1.6 ohms and 1.5mm diameter.
Todays build is with the same Kanthal ribbon, the difference this time is the stacked dual coil… the flavor the Aspire coils produce inspired me to try their same style stacked coil arrangement on the KFL…this one measures out at 1.56 ohms, it's not the prettiest coil on the block but works great, and it's producing more vapor than the single coil ribbon…flavor report by days end tomorrow.
Here's a look at it…
that's exactly it. this doesn't dramatically change the kayfun at all, it just allows more feed potential.
svoemesto I'm sure put a lot of R&D into this atty and I think it's an awesome design with awesome craftsmanship, but I also think the final design is calibrated to suit the masses. I'm sure if the juice delivery could have easily been made adjustable then they may have, but it isn't, it is a fixed orifice. mercedes builds an awesome vehicle but that doesn't mean that amg can't take that vehicle and make it better
enlarging these orifices is not much different from enlarging an air hole in an atty cap. stock it obviously isn't going to have a large air hole but if you vape at higher power then you simply need more air so the air hole is drilled larger.
svoemesto didn't calibrate this thing to feed enough fluid to reliably vape microcoils at 15-20 watts. if he did it would flood more easily for all of the general population that are vaping 7-11 watts. svoemesto designed this thing around a few wraps of light gauge wire wrapped around silica, not for LR 28 ga microcoils or microcoils at 5 and 6 volts. if svoemesto themselves were asked to calibrate this atty to the juice flow of a 20 watt vape guess what they would do to the design? first thing they would do would be to open up the juice channels
nobody needs to hotrod there kayfun, it's not needed at all, but hotrodded it is better for me. right now this thing is working awesome for me, I'm thrilled with the vape I get from it
totally agree. since doing this I have had zero dry hits, not that I really had any before but on occasion with higher wattage builds the flavor was lacking, now the vape seems a little juicier imo. one thing that happened, which doesn't really bother me because I rarely keep in my wicks much more then 4 days but with my last build I had kept my wicks in for like a week, well I guess the hemp kind of got whimpy and maybe couldn't hold as much liquid as when new, but it started gurgling. I rewicked and all was good again
- Status
Similar threads
