Have you tried some dish soap and a toothbrush, boiling water won't always remove imbedded machine oil and other contaminants...some good dish soap and a nice scrub will.
- Status
Whats your mod/coil resistance/volt or watt settings? Doesnt sound right. also take a pic of your wicking and post- that sometimes is the key for burnt hits.
Provari and MVP2. I've probably built approx 7 boils, all between 1.7 and 1.9 ohms. On my MVP 2 i run 8 watts, on my provari I run 4V. pictures below
Hope that can provide some clue on whats wrong. Hate to see that poor sod lying in bits and pieces
Anybody know any tips for filling the kayfun /Russian? I've tried the fill holes and then saw the video where you fill it from the top. I hold the air hole, fill it, but everytime, I get leakage from the air hole after I seal the top cap... Not sure where the pressure is coming from.
Sent from my HTC One using Tapatalk
Sent from my HTC One using Tapatalk
I fill using the fill hole. No leaks, filling from the top was problematic for me make sure all your o-rings are in place and everything is nice and tight before filling and hold it upside down and you should be good to go.
sent from my Limited Edition Monkey Island Talking Voodoo Doll Head named Murray®
Keep finger over air hole when filling, start putting the top cap on until and just catches, flip the Kayfun over and wait a second, then screw the top cap down while still upside down. You flip it over so the air bubble travels to the deck area, so the pressure caused when screwing down releases air instead of juice.
Also, don't fill it up all the way, leave some room for air. I've been usually filling this way and it works great.
Thus you need a dual coiled .8Ω and the power of X...
-34ºC now, and .... frozen
“So when you're cold
From the inside out
And don't know what to do,
Remember love and friendship,
And warmth will come to you.”
~Stephen Cosgrove, Gnome from Nome
A Very Good Morning my friends!
-34ºC now, and .... frozen
“So when you're cold
From the inside out
And don't know what to do,
Remember love and friendship,
And warmth will come to you.”
~Stephen Cosgrove, Gnome from Nome
A Very Good Morning my friends!
In addition to the previous advice, be aware that some juices can expand the 4c o-ring. When that seal is broken, it definitely leaks through the air hole.
If you received a spare, check to see if they're still the same size. If they're not, and you still want to run that juice, there have been links to inexpensive replacements posted in this thread.
Here's a picture from the SvoëMesto Kayfun Lite manual:
Last edited:
Thus you need a dual coiled .8Ω and the power of X...
-34ºC now, and .... frozen
“So when you're cold
From the inside out
And don't know what to do,
Remember love and friendship,
And warmth will come to you.”
~Stephen Cosgrove, Gnome from Nome
A Very Good Morning my friends!
I read you guys are getting yet another cold snap
it's been almost like spring here
I read you guys are getting yet another cold snap
Luck Bs.
But, I'm Ok with the cold... brings you closer to your thoughts (less activity you see!)
Luck Bs.
But, I'm Ok with the cold... brings you closer to your thoughts (less activity you see!)
I hate the cold bro. i'm retiring @ 60 so, 10 more years to go them its south bound for 6 months of the year! I hate winter more and more every year
I must say that I am impressed with the coton yarn in my coil!! It is perfect with removing 1 strand and the vape is awesome. I just can't get the cotton balls consistent with each wick even though I think it is slightly better than the PnC yarn. But I am able to have pretty much the same wick every time!! I will keep practicing with cotton balls and have a roll of sterile cotton to try as well!! But for now, I was surprised how easy the yarn is working out!!
Added a little carbon fiber accent from jwraps to the Russian, wasn't crazy about the original finish, like the KFL finish much better!!
Added a little carbon fiber accent from jwraps to the Russian, wasn't crazy about the original finish, like the KFL finish much better!!
Last edited:
I must say that I am pressed with the coton yarn in my coil!! It is perfect with removing 1 strand and the vape is awesome. I just can't get the cotton balls consistent with each wick even though I think it is slightly better than the PnC yarn. But I am able to have pretty much the same wick every time!! I will keep practicing with cotton balls and have a roll of sterile cotton to try as well!! But for now, I was surprised how easy the yarn is working out!!
Added a little carbon fiber accent from jwraps to the Russian, wasn't crazy about the original finish, like the KFL finish much better!!
that's pretty sweet. I like the carbon look
Hey diver. I was just signing off cuz I'm tired beyond belief but saw your name pop up and thought I'd stop in quick just to say hi. Hope all is good by you.
goodnight.
goodnight.
Thus you need a dual coiled .8Ω and the power of X...
-34ºC now, and .... frozen
So when you're cold
From the inside out
And don't know what to do,
Remember love and friendship,
And warmth will come to you.
~Stephen Cosgrove, Gnome from Nome
A Very Good Morning my friends!
qorax, how you liking the aqua? for me its the aqua under .6 and the kayfun over. the vapes are equal imo, but when I feel the need for super low res vape, the aqua handles it so much better
Provari and MVP2. I've probably built approx 7 boils, all between 1.7 and 1.9 ohms. On my MVP 2 i run 8 watts, on my provari I run 4V. pictures below
Hope that can provide some clue on whats wrong. Hate to see that poor sod lying in bits and pieces
doubt its the insulator. the only thing I see which maynot be the issue and is slightly varied from most builds are, for one it seems like your coil is very low, almost touching the deck. this can produce a gunky coil very fast, thus causing a burnt taste. I would raise it slightly. I like the bottom of the coil about 1/4 below the top of the screw head. also what is the diameter of your coil? if its the 1/16 variety the wick could be slightly to thick, if your diameter is 5/64 it looks close to the correct thickness. but then again its hard to tell from these photos, your coil could be positioned perfectly and im totally wrong. how are you getting clouds from that one photo, I don't see a wick.
hey bro, im doing good, busy but good. I miss this thread a lot. need to post more often. man 700 pages awesome!
Hahah that's the cotton wick. I pulled it up to show the height of the coil. I guess I'll really lift the coil up and try it one last time. Thanks a ton for being patient enough to troubleshoot this with me though!
Sent from my iPhone using Tapatalk
you know what happened once, or at least I think it was the cause. I keep my cotton balls in the package it came in, all sealed up. I usually take out one ball and cut it up into strips and keep these in a separate bag. these strips I use a lot, almost every day or two when rebuilding. well after handeling this cotton for a week or so I think they got spoiled and weren't fresh because maybe I wasn't washing my hands enough. anyways have you used a totally fresh cotton ball? or pieces that been handled maybe to often? just a thought
This is the easiest way I've found to separate the deck from the barrel.
Sent from my SCH-I605 using Tapatalk 2
Sent from my SCH-I605 using Tapatalk 2
- Status
Similar threads
