Kayfun Lite
- Thread starter CerealVapist95
- Start date
- th_trl_thread_readers 0
- Status
I was liking a 30 guage micro coil at 1.4 ohm on my mech with cotton. Now running 1.6 ohm micro coil with 30 guage on my evic to get a little more adjustability on it. I run these in my pro tank and they work better in the KFL.
just made a microcoil chimney build on mine today, and it is rocking it. 1.1 ohms...7 wraps or so around a 5/64 bit with 28 gauge kanthal and cotton wick.
I just ordered 2 kayfun Lite clones yesterday. I can't wait to see what these will do for me. I've been using genny rba's for quite some time now and its time for a change. I plan on using silica first. I have 28, 30 and 32g Kanthal and a few different sizes of silica to play with. What is everyone using on these?
I'm using 32 kanthal with a 7/8 wrap and organic cotton and it works pretty well. I would suggest organic cotton over wick and mesh. Never been a fan of either
Sent from my iPhone using Tapatalk
Not so sure for a mech mod. I am using regulated mods, although the VTR will fire down to .5ohm. That being said, it is my experience with the KFL+ that it will be really good with pretty much anything you throw at it. I am currently using a 3 strand 32ga twisted micro coil at 1ohm. I had to toy a bit with wicking and air flow to properly feed the beast, but it is working just fine now that that is figured out.
I have also done 28ga and 30ga coils with no problems and good performance as well.
I have also done 28ga and 30ga coils with no problems and good performance as well.
Dual 28g nano coils with cotton works the best for me. I love the amount of vapor and the warmth this setup gives.
Currently running a 30g 1.4ohm microcoil with cotton wick. I need to tear it down and replace the wick though, I got a bit too much cotton and it's giving occasional dry hits.
2Turbo Slaab
Could you please shouw a picture of 2 microcoils on Kayfun? Is it too warm? I like more the cold vapor or lets say not really hot.
Could you please shouw a picture of 2 microcoils on Kayfun? Is it too warm? I like more the cold vapor or lets say not really hot.
I want to use silica because I find that cotton needs to be replaced too often. I'm using cotton now in my gennies and I have to replace it every 2 tank fills. I will try cotton later I'm sure. Might try 32g on my first builds and see how it works. I only use 100% PG liquids also.
I can.
But that's not the most impressive one I've seen.......... this is....
I have no idea how well it works, but the craftsmanship is really impressive.
I've been experimenting with different builds over the past few days, and I've really come to like a chimney coil with 28g and a double barrel micro coil also with 28g, both with organic cotton. I actually would not suggest 32 I had to use it again today cause I ran out of 28g and not having 28 made me realize how dinky the 32g is. Watch RIPTripper on you tube's video on the chimney and double barrel builds.
Sent from my iPhone using Tapatalk
I ordered 2 and only got one today... .....! I emailed him and thankfully he still had the other. When I ordered them he only had 4 left in stock when I ordered the 2. Soon after my order, he was sold out. He better have my second one shipped today. I use 2 different liquids and use one liquid a day. I hate swapping liquids in the same device but I want to use the Kayfun. My first set up was with 2mm silica folded 3 times with the loops sucking the liquid with 32g kanthal. Its burning at 2.2Ω but I think I want lower.
If you want your cottom to last long get some BioWick. Mine lasts forever. Ive never had to replace the wick until the coil needed dry burning. I vaped an entire 50ml of VapeDudes Cool Melon 12mg 50/50 and the cotton and coil wasnt even brown
Sent from my Samsung Galaxy Note 3 using Tapatalk
Sent from my Samsung Galaxy Note 3 using Tapatalk
Also i use 28ga kanthal 8-10 wraps on a 1/16th drill bit for a nice long coil. I remove two strands of cottom from the BioWick and i do the standard "S" shape with wick where my coil is angled, 2mm above deck and wicks laying flat on juice deck.
Sent from my Samsung Galaxy Note 3 using Tapatalk
Sent from my Samsung Galaxy Note 3 using Tapatalk
This will be a lot of playing around to find the best set up. I have some Ekowool Solid Silica Cord 3mm that actually looks like its 4mm thick that I want to try next. Does anyone use a thick wick like this?
My problem with 28g (Which seems to be the most popular) is the amount of time it takes to heat up.
If you built two coils of the same ohm, one with 28g and one with 30g, the 30g coil will heat up faster. The wire itself has a higher electrical resistance so it will heat faster even though both coils have the same ohm reading.
I have the KFL clone, but its not too different from the original. Right now im running a nanocoil with 26g wire on a cotton cloud. I wrapped it around 28g wire. Its super tiny but the vapor is incredible. Its fires at 0.7 ohms. Best build I've found so far.
- Status
Similar threads
