- Status
Nothing installed in the atomizer or loose in the parcel with it, unfortunately. Fortunately, I found not one but two old CE2s that I was able to take apart to have a ceramic to get this thing working and have a backup on hand! Despite my comments about the appearance, it screws together fine and vapes just the same! :]
Mine should be delivered today.
It's dumping down snow right now though. Let's see how well the post office motto holds up...
How long did it take from the time you ordered until it reaches your mailbox today (hopefully).
How long did it take from the time you ordered until it reaches your mailbox today (hopefully).
Shipped on the 5th. Going on 11 days now.
It still doesn't say 'out for delivery" even though another package does. Maybe it's not updating, but it took 2 days to get from Raleigh sort facility to Cary P.O. (about 10-15 miles apart, normally takes 1 day).
So we'll see. I might not get it til Tuesday... grumble...
Ordered from greekvapes.
That's where I ordered from too. 11 days isn't too bad. I have packages that sit for 2 days 50 miles from my home. It's very frustrating. I hope you get it today and post what you think of it.
That's where I ordered from too. 11 days isn't too bad. I have packages that sit for 2 days 50 miles from my home. It's very frustrating. I hope you get it today and post what you think of it.
Thanks! It made it today. I could hardly keep calm.. Got her in a Phiniac, and filled it up. So far it's vaping great.
I'm going to have to get used to this though. I already have a short list of questions. I'll report back later.
I'm glad it fits in a Phiniac because that where mine's going. Do you have it in a reg size or a tall boy tank? Oh and are you using the setup that came with it?
In a regular Phiniac.
I'm using the stock setup.. I had little desire to rebuild this thing at the moment, I just want to see how it works.
Good on the Phiniac. Do you think it would fit in a Tall Boy? And I'll probably do the same and use the stock setup just to see how it works.
Good on the Phiniac. Do you think it would fit in a Tall Boy? And I'll probably do the same and use the stock setup just to see how it works.
You can use the tall one if you have a straight drip tip (same circumference as the Killer or a carto).
Already rewicked this puppy (I hate silica). I have cotton yarn running through the coil, and a bit of sera wool stuffed under the ceramic cup. Letting it soak in a bit, but I have high hopes.
I didn't think it would take you long before you rebuild that coil. Everybody says it tastes like 
I like cotton better also and with the cotton being constantly wet it should last longer than in some RBAs.
I don't mind silica at all, but I guess I've never tried anything else. The Killer is still vaping great, but it hasn't been getting a lot of playing time since I got my new Russian toy (Kayfun). I may put this one up in the classified soon enough (once I get verified) PM me if you are interested.
Last edited:
I've had my Killer 705 a number of days now. When it works, it works great. I was experiencing dryer & harsher hits. I chucked it in a pocket for a couple of days and took it out this morning. Nice, then started going south. So I pried up the top of the j-tank I'm using and bubbles streamed out of the bottom fill holes. That would indicate that there is some type of vacuum getting set up inside the Killer itself not allowing fresh juice to enter and get up to the wicks.
Don't know what to do about this just yet. I don't want to have to be prying up the top cap all day long. I'll use it most of the day today to see if this continues.
Any suggestions?
Don't know what to do about this just yet. I don't want to have to be prying up the top cap all day long. I'll use it most of the day today to see if this continues.
Any suggestions?
Sounds like air lock. Try giving a few blows in to try and free the air bubble. Works with the reactor atty tank so I can't see why thins would be different.
Sent from my iPhone 5 using Tapatalk
Sent from my iPhone 5 using Tapatalk
I haven't received my killer yet so I'm not all that familiar with it but if the juice control is slightly open when you put the top cap back on try to have an air bubble in the tank over the juice intake before snapping on the top cap. That should release any pressure build up. That's what I do with all my cartos so I don't see why that wouldn't work with the killer.
So you are saying that if I snap the top cap into place, that can force a bubble lock down in the Killer filler holes or somewhere inside? Would this mean that whenever I push the tank together, just be sure that there is air surrounding at least one of the filler holes?
Thats the way we do the reactor. Just set the top cap in place lightly (enough not to leak) then tilt until the air hole is in the air bubble from the juice, then snap the top cap in place. Then take a couple quick dry pulls, short sharp ones, then vape. I dont have my killer yet but that is the procedure I use for my reactor.
- Status
Similar threads
