listing side by side mods
- Thread starter drugarth
- Start date
- th_trl_thread_readers 0
It's a complicated and s-l-o-w process. I tap on individual letters, one at a time, then hit this arrow thingie in the corner and wait, wait, wait... Does that help?How'd you do that, by the way?
I couldn't resist, Kat.
Sent from my LGLS992 using Tapatalk
see below.
Yeah I am at that has to be extra sweet junction too.
I am liking the Pico very much KD. It is approved and at 70mm high I believe it is the shortest 18650 regulated mod available. I'm not a eleaf fan but this one is sweet. YMMV
Pocket lock, this when your mod goes sideways in your pocket, stretches the pocket fabric slightly and is then wedged into the pocket. It is horrible!
Welp, you set me all aglow looking over all my spreadsheets today (and it was a needed chore). At current usage, with what's on hand, we'll have enuf for ........
12.3958333333333333333333 years!!!!!!!!!!!!
I hope at least 5 years
and then I also have about 50 triton mini's for the Plato....is there a half-life time for coils? 
If anyone wants to go really old school, Vapage has their lil' stealth vmod on sale for $25. That's the lowest price I've seen.
Sent from my LGLS992 using Tapatalk
Sent from my LGLS992 using Tapatalk
For those looking for more capacity in their Kabuki's...
I just saw a post in a Facebook group where someone put the 5ml Aspire Cleito tank on their Kabuki and it fit! A little taller than stock so the juice holes are fully exposed, but the diameter was a good fit. Doesn't look like it would fit inside a "seat belt" though...
Ok, the shelf live of a Nautilus coil is 12.3958333333333333333333 years.
dru........ curious..... the 5ml tank sounds pretty sweet in the Seatbelt mod.... but what do you mean that it doesn't look like it would fit? Why not? If it fits the Kabuki.....
It gets FAT in the middle like the Kayfun v4 does only a bit more pronounced. If it ends up being the same diameter as the Kayfun v4 it should fit though, I use the v4 in my Knight with no issues...Ok, the shelf live of a Nautilus coil is 12.3958333333333333333333 years.
dru........ curious..... the 5ml tank sounds pretty sweet in the Seatbelt mod.... but what do you mean that it doesn't look like it would fit? Why not? If it fits the Kabuki.....
Aspire Cleito Replacement PYREX Glass Tube (5ml)
AHA. Thanks, k2. I hadn't glanced at the pic of it. Now I see what you mean about fat in the middle (much like most of us...... I better not go there ).
).
Yup! Just got to it late last night. Seems made for each other.
Sent from my iPhone using Tapatalk
Yup! Just got to it late last night. Seems made for each other.
Sent from my iPhone using Tapatalk
Indeed!!!
Any early thoughts?
No rush - just wondering...
Literally just started using it 5 min. ago.
I like the way it looks and feels. Definitely feels like a quality mod. I would think that it would be a little heavy for you.
I'll check back in after a few hours.
Sent from my iPhone using Tapatalk
It feels very similar to the Xvo, weight-wise. A bit heavier, but quite manageable.
Out of curiosity (after typing the previous sentence), I checked them both - fully loaded. The Rolo is 12% heavier. So yeah, it's manageable.
Quick question- did anyone other than me buy the RBA deck for the Smoant/Talos tank? Mine is absolute trash!!!!
The deck screws barely hold the wire in place & the deck itself is loose. I've tightened it up as much as I could but it's still loose.
Also, the screw that holds the chimney in place is so far recessed into the tank that it makes cotton swapping a chore cause the whole thing needs to be removed. The deck itself looks extremely similar to a Kanger RBA deck for the exception of the chimney screw being a tad bit higher.
I tried using a Kanger deck in the Talos but it comes up "no atomizer".
The deck screws barely hold the wire in place & the deck itself is loose. I've tightened it up as much as I could but it's still loose.
Also, the screw that holds the chimney in place is so far recessed into the tank that it makes cotton swapping a chore cause the whole thing needs to be removed. The deck itself looks extremely similar to a Kanger RBA deck for the exception of the chimney screw being a tad bit higher.
I tried using a Kanger deck in the Talos but it comes up "no atomizer".
Any way to swap center posts? Thought the Talos RBA was same as the Smoat one.
Last edited:
