Milled catch cups and oversized atomizers
- Thread starter pdib
- Start date
- th_trl_thread_readers 0
- Status
Ditto x2.
In terms of best drippers for me the quasar and patriot. The downfall of the Cyclone is the small deck which can limit builds which usually led to less wick and more dripping. I love slotted airflow. The double cross is another solid rda.
The Helios is a great design for many but I wish the airflow was slotted and that they included a single coil airflow option. Too expensive for what it is imo. For reo owners small caps are best for flavor and room for the button. Plus they look better not hanging over the sides. The igo-T is actually closer in terms of looks on the two. In my opinion it's hard to top the afc Cyclone.
Sent from my SM-N900V using Tapatalk
I had a bit of leaking from my modded trident, but after I adjusted my squonk, I have no issues. I can also close the holes by spinning the air flow control cap before I pocket my reo. Unless I put it in my pocket upside down, no leaking at all.
man with hole in pocket feel cocky all day?
Still not sure about the trident - i don't like those micros.
T
Still not sure about the trident - i don't like those micros.
T
I just shelved both my Grands.. one milled, one stock.
Until i get some sub ohms kit … can't keep them stock for more than a few days at a time; if that.
2 collapsed springs, and muddled pos pins…
I was getting better flavor on my RM2 this week than the Cyclone AFC (lots of less flavorful vapor)… dunno why though.
I think the experts are modding the cyclone to drain better too.
Until i get some sub ohms kit … can't keep them stock for more than a few days at a time; if that.
2 collapsed springs, and muddled pos pins…
I was getting better flavor on my RM2 this week than the Cyclone AFC (lots of less flavorful vapor)… dunno why though.
I think the experts are modding the cyclone to drain better too.
i'd be more worried about why you are collapsing springs, because it's likely the atty. I have not wrecked a grand spring yet but i am trying!
milled or not makes no difference.
T
milled or not makes no difference.
T
Don't have to build micros on any atty man. Build it how you see fit.
Confucius say: Man who stand on toilet... High on pot
I'm always pushing the limit… 'cuzzz thatz how i rolllllll…. bwahahhh
actually a lazy not very handy man when it comes to tech and so i use stock with sub ohms… first atty in my new milled Grand was the Cyclone AFC with dual coils = .45 Ohms = new spring tweaked. Chain hitting it confungled the button and pin.
I mainly relegate my Reo's for the road mobile, but until my set of kits arrive from Rob…. same time you guys get yours, i'll use my dripper tanks in the vehicle.
Gryphon and Big Ben get 2 to 4 mil of juice in… to top off too many high end mechanical tubes
actually a lazy not very handy man when it comes to tech and so i use stock with sub ohms… first atty in my new milled Grand was the Cyclone AFC with dual coils = .45 Ohms = new spring tweaked. Chain hitting it confungled the button and pin.
I mainly relegate my Reo's for the road mobile, but until my set of kits arrive from Rob…. same time you guys get yours, i'll use my dripper tanks in the vehicle.
Gryphon and Big Ben get 2 to 4 mil of juice in… to top off too many high end mechanical tubes
i'd not dare run coils that low without the fuse and i might just end up doing that when the new firing pin comes out. I'm at about 0.6 for daily use, but Xobe is sending me some Mundy Magic and then all bets are off.
I run orbtronic high drains in a grand and i just got a couple more - these are the sx30s and i rather like the power output of them. Certainly as good as my Samsungs and MNKEs. I am gradually phasing out my year old EH and EFESTs, i cannot prove it but i know they are wilting.
T
I run orbtronic high drains in a grand and i just got a couple more - these are the sx30s and i rather like the power output of them. Certainly as good as my Samsungs and MNKEs. I am gradually phasing out my year old EH and EFESTs, i cannot prove it but i know they are wilting.
T
you can prove it. do a v-drop test at your atty posts with your old batts vs your newer ones. That battery internal resistance really does build up and it shows pretty clearly.
That's pretty much my setup right now. Cyclone afc with .48 ohm duals. Honestly the fuse mod is really simple and no problems chaining it so far. Granted I made a new firing pin but the fuse made the bigger difference to me.
Also I'm kinda hoping that the sub kit isn't designed to collapse because I want it to pull everything it can voltage wise. Sure it will take more on my part to make sure everything works correctly but that's what I like about mech mods.
Sent from my SM-N900V using Tapatalk
Sitting here, just recoiled my two reo's one milled Grand and one 2.1, the later has a modded a6 atomizer and the grand has a modded nimbus replica (3 air holes stock) did the same builds on both, 2mm ekowool, 28g kanthal 3/4 wraps. The mini got that smooth sweet vape I want and the grand is almost to harsh. Both coils are positioned close to the holes. Can't really figure it out. I use the same nimbus replica (unmodded) as a dripper and it's great. So yeah can't really figure it out.
Sent from my GT-I9505 using Tapatalk
Sent from my GT-I9505 using Tapatalk
I have a question for u guys with milled grands running unmilled rm2. Mine won't seat on the o ring that came with the rm. Isn't it supposed to?
Sent from my HTC6500LVW using Tapatalk
Sent from my HTC6500LVW using Tapatalk
This is as far as mine will go without cranking it.
Sent from my HTC6500LVW using Tapatalk
Sent from my HTC6500LVW using Tapatalk
if you place a drip tip o-ring around the 510 threads on the atty, it seals it up nicely.
- Status
Similar threads
- Locked
