Like the title says I modded it.
I have a way of modding most everything to better suit my own needs/ likes. Seems vaping is not immune from this trait of mine.
Bought a kayfun clone to go on a Nemesis clone, and liked it more than the iTaste MVP or Ego's I was using beforehand....but....It could be better IMHO.
First thing I didn't like was the small hole in the tip. Didn't like having to suck on the thing for what seemed like 15 minutes (probably more like 20-25 seconds) to get a decent pull. Was also a little harsh on the back of my throat (hot maybe? Nic on my juice is at 10mg).
Screwed on the drip tip adapter that came with it, and tried different style drip tips I had to figure out what hole size I liked best.
Found 4.5mm or .175" was the size I liked best.
I could have left it like that but the look wasn't appealing to me, and although I like a drip tip on my dripping atomizer I did not want one on the KayFun since that is on my pocket/ carry along vape set up.
Off to the lathe, and center drilled out the top of the KayFun tip to that size. Deburred the end, and slightly countersunk. Buffed out with red scotch brite.
Nice. That took care of the hard draw, and also the burn at the back of my throat.
Next......I like big vapor. I know I can get thicker vapor by allowing air in around the tip when I pull on my vape.
Honestly IMHO a pain in the backside, and different than the pull I would take on a cigarette (when I was smoking) so again I could have stopped there but wanted my normal pull with thicker vapor.
Hmmmm, Allow more air in just like with the gap in the mouth method but through a vent hole in the KayFun mouthpiece instead.
Off to the drill press, and bored a .043" hole at the base of the mouthpiece.
Sweet! Now I have my normal draw with the thick vapor I want.
Lastly the Kayfun clone I bought at the local smoke shop had the bead blasted finish which didn't match the Nemesis clone I was running it on. Again I could have just been happy with it, and left it alone but as I said before.....It's in my nature to mod EVERYTHING.
Chucked up the KayFun in the lathe, and took the red scotch brite to it to mimic the #4 brushed finish for the Nemesis clone it was paired with.
Not bad.
Now Nico is a happy vaper with this set up with a 1.3 Ohm micro coil (chimney config), and some DIY 7% yellow cake, 4% Cinnamon Danish, 3% Bavarian cream 50/50 juice (Thanks Savagemann for the Juice.....Nico is loving the flavor, and makes the shop smell fantastic).
Just thought I would share what I did in case someone else might like what I had done for their own gear.
I have a way of modding most everything to better suit my own needs/ likes. Seems vaping is not immune from this trait of mine.
Bought a kayfun clone to go on a Nemesis clone, and liked it more than the iTaste MVP or Ego's I was using beforehand....but....It could be better IMHO.
First thing I didn't like was the small hole in the tip. Didn't like having to suck on the thing for what seemed like 15 minutes (probably more like 20-25 seconds) to get a decent pull. Was also a little harsh on the back of my throat (hot maybe? Nic on my juice is at 10mg).
Screwed on the drip tip adapter that came with it, and tried different style drip tips I had to figure out what hole size I liked best.
Found 4.5mm or .175" was the size I liked best.
I could have left it like that but the look wasn't appealing to me, and although I like a drip tip on my dripping atomizer I did not want one on the KayFun since that is on my pocket/ carry along vape set up.
Off to the lathe, and center drilled out the top of the KayFun tip to that size. Deburred the end, and slightly countersunk. Buffed out with red scotch brite.
Nice. That took care of the hard draw, and also the burn at the back of my throat.
Next......I like big vapor. I know I can get thicker vapor by allowing air in around the tip when I pull on my vape.
Honestly IMHO a pain in the backside, and different than the pull I would take on a cigarette (when I was smoking) so again I could have stopped there but wanted my normal pull with thicker vapor.
Hmmmm, Allow more air in just like with the gap in the mouth method but through a vent hole in the KayFun mouthpiece instead.
Off to the drill press, and bored a .043" hole at the base of the mouthpiece.
Sweet! Now I have my normal draw with the thick vapor I want.
Lastly the Kayfun clone I bought at the local smoke shop had the bead blasted finish which didn't match the Nemesis clone I was running it on. Again I could have just been happy with it, and left it alone but as I said before.....It's in my nature to mod EVERYTHING.
Chucked up the KayFun in the lathe, and took the red scotch brite to it to mimic the #4 brushed finish for the Nemesis clone it was paired with.
Not bad.
Now Nico is a happy vaper with this set up with a 1.3 Ohm micro coil (chimney config), and some DIY 7% yellow cake, 4% Cinnamon Danish, 3% Bavarian cream 50/50 juice (Thanks Savagemann for the Juice.....Nico is loving the flavor, and makes the shop smell fantastic).
Just thought I would share what I did in case someone else might like what I had done for their own gear.
