New & Bigger Phoenix XL Rebuildable Atomizer

[Optimo]

Just a quick video showing the difference between the Phoenix RA and the new Phoenix XL RA. Full review coming soon so subscribe and stay tuned!



Direct link

Thanks for watching...happy vaping!

 

[Infinite]

Thanks for the post and heads up! I am still waiting for your expanded video for the Phoenix wicking tutorial, thanks to u though I am getting the hang of coiling. I got my Phoenix last week. And will mos def be getting an XL now too!

 

[pounder]

Optimo. Thanks for the great review of the Xl Phoenix Ra. Will you be trying a ss mesh on this one?

 

[Optimo]

Optimo. Thanks for the great review of the Xl Phoenix Ra. Will you be trying a ss mesh on this one?

I actually just made a new video showing my SS mesh setup on the Phoenix XL. Here's a link: Phoenix XL Rebuildable Follow-up & Using SS Mesh With Silica Wick - YouTube

 

[dnrtn2342]

where can i get a phoenix xl?

 

[Optimo]

where can i get a phoenix xl?

Eshotsph.com it will be up in a few days. You'll be able to get them from places like Liberty-Flights and Vapor..... also.

 

[pounder]

Optimo.Thanks for the heads up on where to get the Phoenix Xl. Now im gonna go watch you do your magic on it with the ss mesh.

 

[pounder]

Optimo. Have you tried the ssmesh and siica set up on the standared size Phoenix?

 

[Optimo]

Optimo. Have you tried the ssmesh and siica set up on the standared size Phoenix?

Yeah it works great. I turned one of my posts so I can stick it in the center. Be careful turning the posts though don't use too much force. I just stuck a needle inside the post hole and gave it a slight turn.

 

[pounder]

Optimo. Ijust built a ssmesh wick over the silaca with a 3/2 wrap with fantastic results. Tons of vapor,th and the flavor is spot on. Thank you for making the tutorial on this set up.

 

[Optimo]

Optimo. Ijust built a ssmesh wick over the silaca with a 3/2 wrap with fantastic results. Tons of vapor,th and the flavor is spot on. Thank you for making the tutorial on this set up.

No problem...glad it's working so good for you

 

[Dragoncqb]

Great vids, my pheonix's will be hear today. But now I have to get the XL's it's a never ending deal ahhhhhhhhh ! . Any way wear do you get your kanthol & mesh ?

 

[Optimo]

Great vids, my pheonix's will be hear today. But now I have to get the XL's it's a never ending deal ahhhhhhhhh ! . Any way wear do you get your kanthol & mesh ?

Stormys Vapor Cellar has everything from wire to wick to SS mesh.

 

[gadabout]

just poppin in to say thanks to optimo for takin his time to help us all out on rebuilding these things to get the best results! thanks man

 

[gadabout]

another question is dhould i unravel the 3mm wick..or leave it together for the ss.

 

[Optimo]

another question is dhould i unravel the 3mm wick..or leave it together for the ss.

I would leave it together and just fluff it up a bit before wrapping the mesh around it. Once you put the mesh on it just roll it around in your fingers to tighten it down onto the wick. You want it so it's not too loose but not too tight either...just to where it can barley move side to side on the wick when force is used.

 

[gadabout]

havent gotten the ss yet..but got some new wick. made a coil..it first read 1.8 ohms..tasted a little better then the old wick i had..but still an off taste. then read my ohms again..it was 2.5. adjusted voltage..and 20 min later..2.0 ohms. what would be causing this..thanks

 

[Optimo]

havent gotten the ss yet..but got some new wick. made a coil..it first read 1.8 ohms..tasted a little better then the old wick i had..but still an off taste. then read my ohms again..it was 2.5. adjusted voltage..and 20 min later..2.0 ohms. what would be causing this..thanks

Sounds like the coils are either shorting out/touching each other or touching the posts/casing. Make sure you cliped off all the wire you can after running it through the post holes as that can touch the sides/shell and case shorts also.

 

[aktionze]

Hello Optimo,

I am one of your viewers on the forum and YouTube. I have been fan of your videos and reviews since I got into vaping. Recently, I watched this video while I am searching for a new tank or cartomizer or atomizer for my first time VV (Lava Tube). It is really a great video and now I really want one.

However, if you don't mind, can I ask you some questions? For flavor and clean vaping, which one would you recommend? tank or cartomizer or atomizer. Also, for Pheonix Rebuildable Atomizer, where can I get all the supplies? Phoenix, ss mesh, silica wicks, etc?

I would be very appreciated if you could answer my questions. Thank you, Optimo

 

[Optimo]

Hello Optimo,

I am one of your viewers on the forum and YouTube. I have been fan of your videos and reviews since I got into vaping. Recently, I watched this video while I am searching for a new tank or cartomizer or atomizer for my first time VV (Lava Tube). It is really a great video and now I really want one.

However, if you don't mind, can I ask you some questions? For flavor and clean vaping, which one would you recommend? tank or cartomizer or atomizer. Also, for Pheonix Rebuildable Atomizer, where can I get all the supplies? Phoenix, ss mesh, silica wicks, etc?

I would be very appreciated if you could answer my questions. Thank you, Optimo

Atomizers will have the best flavor but carto tanks arn't bad for a hassle free vape. The Phoenix will have a even better flavor than your standard atomizer. You can get everything you need from DIY Rebuildable Atomizer Parts : Stormys Vapor Cellar, Electronic Cigarettes & More

You might be able to find it cheaper on ebay though.