lmao the damn thing is in my house within a 15' x 15' area. You think I could find it??? I looked for an over hour!!!You beat me to it.That's what I was going to suggest K-man.
New Genesis type atomizer by DID!
- Thread starter Jim Damianidis
- Start date
- th_trl_thread_readers 0
- Status
Thanks!! Added it to my Amazon wish list. It says it has a little circle with 6x zoom for finer detail. That just might do the trick!
Jim, what to use to isolate the wick from the hole in the atomizer to prevent it from shorting (like in a Zenisis)?
Are you going to sell this on your site?
Are you going to sell this on your site?
Why can't you just use a food grade sealant and line the edge of the hole with it? My work sells some that is resistant against acidic juices and heat up to 1200 degrees. It's what I was thinking about doing.
Beautifully.
3.7 (the volt depends upon the wrap. The less wraps you have, the lower the resistance is. The more wraps, the higher the resistance. I recommend starting at 3.0 and working your way up to pure happiness and then stop before you burn your juice. More is not always better.)
@ K-man. Here's a wick / coil trick trick I picked up on ob's Coil & wick tips & tricks thread "peter k" method and it works great with just the bottom nut and one securing nut. I did cut the mesh @ 15mm +/- wide & 30+mm tall to fill the DID's hole a bit more. What clicked with me about this method was what Peter K said. "It wicks, and watts are not spent for mesh heating, but for
e-liquid."
This is a 4/4 coil and is great @ 3.6 /3.8 V, and will flood at horizontal if your not careful.
e-liquid."
This is a 4/4 coil and is great @ 3.6 /3.8 V, and will flood at horizontal if your not careful.
I was hoping mine would make it in before the holiday and find it's perch atop my silver Buzzpro 
after seeing all of these pictures of them on everybody's mods.I know patience is supposedly a virtue but,I just think I was left out of the line when it was being handed out.
after seeing all of these pictures of them on everybody's mods.I know patience is supposedly a virtue but,I just think I was left out of the line when it was being handed out.If I would have know that somebody so close to me was getting a DID this week it would have been tempting to stalk your mailman instead of waiting in mine
Well,just checked the tracking on usps and shockingly I got this nice surprise:
Processed Through Sort Facility
July 03, 2012, 7:05 pm
ISC NEW YORK NY(USPS)
Now,hopefully it won't take them too long to finish up it's trip here!
Processed Through Sort Facility
July 03, 2012, 7:05 pm
ISC NEW YORK NY(USPS)
Now,hopefully it won't take them too long to finish up it's trip here!
I met the carrier at the box.If I would have know that somebody so close to me was getting a DID this week it would have been tempting to stalk your mailman instead of waiting in mine
As far as everyone's concern with isolating the wick from the hole, what I did was the cigarette paper trick, but extended it into the hole. The paper burns off under the coil, but some is left to insulate the hole/wick.
Last edited:
spoke too soon lol, tank got dry and I didn't realize it but I popped the coil messing around with it. I did notice though that the 2 nuts that clamp the kanthal are more or less a hassle to deal with cause you end up snugging the wire and trying to get them tight. I took the advice of another member on here and just pulled them off wrapping the kanthal directly on the post instead. Made life alot easier and my coil is now at 2.5ohms and has no hot spots and is working better than my first coil was. It also got rid of another spot for the kanthal to short out on so it may be worth a try on your next rebuild, i bumped my wick and the second coil shorted on the nut causing an f1 on the vmax cause it made the wick seem shorter than it was of course. Anyways a few pictures of the combo and what my coil looks like without the nuts on it.
Hmmm, ok, now I'm worried. I have #640 too- is that possible? email stated it shipped 6/20 and was combined with another order but the tracking number still says its in Greece? This was a large order
Hmmm, ok, now I'm worried. I have #640 too- is that possible? email stated it shipped 6/20 and was combined with another order but the tracking number still says its in Greece? This was a large order
Now,that would worry me too but,I'm sure there is a simple explanation for it.Sorry for our troubles and hopefully it arrives safe and sound and the same goes for all of them still en-route to their owners.
I agree, just oxidize it well, and no problem. Roll wick tight enough so it goes into the well smoothly without much friction which could strip away carbon and cause short.
Sent from my cm_tenderloin using Tapatalk 2
- Status
Similar threads
