DID STEALTH DESIGN BUTTON !!
Do you like it DSpin? Really?
I like it !!!!
and as I see I like what most people like!
Quality / Simplycity / Design / Fanctionality / ENGRAVINGS
You're forgetting about something
New Genesis type atomizer by DID!
- Thread starter Jim Damianidis
- Start date
- th_trl_thread_readers 0
- Status
You're forgetting about something
If you blend a Poldiac and it still works afterwards, I want to buy that Poldiac...you need to put a blender engraving on it though! That will be an epic collectors piece once the poldiac really takes off!
Fair enough!
So on another note, Dspin bullied me into testing out the all brass GGTS and brass 4 in 1 top cap I just got in from COV earlier this week, which until 10 minutes ago had gone completely unused and went straight from the priority mail box it came in, to the buffing wheels, and then into my glass display case. So I put my short DID (pyrex tank, brass contacts, 7mg Pluid, 0.6Ω or so coil, and 3-airhole top cap) on there and popped in a fresh MNKE IMR 18650, and after 5 good pulls, I don't think I've ever been so nic sick in my life. If I can handle it, I'm going to try and film a brief demo of the brass GG+short DID setup, bc I don't think I've ever had any other setup destroy me quite like this ....... just did. Been awake for 42 hours, signing off!
So on another note, Dspin bullied me into testing out the all brass GGTS and brass 4 in 1 top cap I just got in from COV earlier this week, which until 10 minutes ago had gone completely unused and went straight from the priority mail box it came in, to the buffing wheels, and then into my glass display case. So I put my short DID (pyrex tank, brass contacts, 7mg Pluid, 0.6Ω or so coil, and 3-airhole top cap) on there and popped in a fresh MNKE IMR 18650, and after 5 good pulls, I don't think I've ever been so nic sick in my life. If I can handle it, I'm going to try and film a brief demo of the brass GG+short DID setup, bc I don't think I've ever had any other setup destroy me quite like this ....... just did. Been awake for 42 hours, signing off!
Brass is the softer metal and should not hurt the DID stainless male connector , you can try penetrating oil in small cup and let it sit then cover with rag and use channel lock type pliers but just get that on to grip it over the rag to turn do not grip it to point it mashes it you just want firm grip to turn it.
Last edited:
Put a paper towel on it and use your teeth. That what I would do. You can control how hard you are biting. Just enough to keep it from turning. Tiger style.
Tony
Yes, brass threads versus stainless threads: stainless wins.
Last edited:
Its just like in Jims picture Rick and the freezing did not work unfortunately .
Thanks Tony mine is the recessed connector so those grooves are under the threads not sticking out like the classic connector.The Did is vaping like a train on the roller though
Thanks Tony mine is the recessed connector so those grooves are under the threads not sticking out like the classic connector.The Did is vaping like a train on the roller though
Did you use your teeth. I'm not kidding.
Tony
Keep your teeths and do not listen to Tony!
Please try to heat only the brass with a lighter wile you slowly turn around the stuck parts!
then put water in your siringe and let drops fall in the center - positive pole and try to unscrew with gloves
or second do what I posted before!!
My wishes!!
I hope it works!!
Please try to heat only the brass with a lighter wile you slowly turn around the stuck parts!
then put water in your siringe and let drops fall in the center - positive pole and try to unscrew with gloves
or second do what I posted before!!
My wishes!!
I hope it works!!
Last edited:
Yes Jim it was and it is the recessed connector so the grooves do not stick out , they are under the threads more.
Thanks Jim, I am trying everything
Not everything.
Jim is right. Im just crazy. In ny you could pay a bum a buck to do it for you. LolTony
- Status
Similar threads
