New Genesis type atomizer by DID!

Status
Not open for further replies.

Tonytiger1

Ultra Member
ECF Veteran
Jan 22, 2012
1,279
4,026
Houston
Me and my buddy Pol spinning some Janis Pearl.

2aravyme.jpg

That's a serious turn table. Are you running some vandersteen speakers to.


Tony
 

NatGasMan

Ultra Member
ECF Veteran
Verified Member
Jun 7, 2012
2,363
7,179
Not in Colorado yet!
We need to meet and knock back a few! You flying this weekend? Where in town do you live? BTW, I was in the Army as a tanker (big guns) from 84-88. I heard your son was about to start sniper school soon. Gary Owens.

Steve Miller spinning now. Come on pretty baby, we're gonna raise a family. LOL!
 
Last edited:

Cloud Wizard

Ultra Member
ECF Veteran
Verified Member
Feb 24, 2012
2,315
5,684
Somewhere in PA on my Ultra Limited
Okay, I gotta ask, since I no longer see the Timon Set on the website. Is it going to be produced again or is it discontinued??

Sincerely;
Nate
Hey Nate, that's what I'm waiting for too. Jim said it'll be there soon (couple days, couple weeks? - don't know)
 

Cloud Wizard

Ultra Member
ECF Veteran
Verified Member
Feb 24, 2012
2,315
5,684
Somewhere in PA on my Ultra Limited
I do have a question about DIY. is it more cost effective to buy the 100 mg base versus the 48 mg that I have been buying? I have purposely been buying the 48 mg strength because of the dangers of 100 mg base. Please remember that I just started DIYing.

Nic base will always be the more expensive component. As long as you're careful about your mixing, higher concentrate nic solution will be cheaper.
 

Cloud Wizard

Ultra Member
ECF Veteran
Verified Member
Feb 24, 2012
2,315
5,684
Somewhere in PA on my Ultra Limited
Well, I am vaping on Poldiac/Gemini right now with #500 unoxidized wick and 30g 4/3 coil Peter K method, save time and resource on oxidizing. I like it! and thank you Inspirer;)

Hoey, you gotta try ribbon wire. I'm wrapping the 0,6 these days and it's more tolerant (hot spot/short wise) and tastes great!
 

NatGasMan

Ultra Member
ECF Veteran
Verified Member
Jun 7, 2012
2,363
7,179
Not in Colorado yet!
NatGas you're a wild man tonight! That Maker's Mark is alright...

Hell yeah. Switched to the hard stuff...Rage Against the Machine. "$uc& you, I won't do you tell me!" Bad day at work. Just wish I could put a coulple of 105mm into some targets about now.

I may be old, but have always kept up so to say. Always been a metal fan. But, I love all kinds of music. It was always my escape so to speak.
 

Cloud Wizard

Ultra Member
ECF Veteran
Verified Member
Feb 24, 2012
2,315
5,684
Somewhere in PA on my Ultra Limited
Thanks for the answer jhjonson123. Would you guys consider .6 and .8 to be reasonably safe for vaping on a mechanical mod like the Poldiac? I just want to make sure that I am being as safe as possible when vaping. Of course I am using aw imr bats.

I would love to see Jim do some Rhodium plating for contacts and such, that would be so nice not to have to clean the silver all the time. I know its expensive to do, but I would def. pay him for it.

I stick to 0.7+ (usually 0.8) but very safe as long as you're keeping an eye on your batteries. DO NOT let them over discharge (below ~3.3v) as this will damage them. On the rhodium thing, Jim puts 15 micron of Silver on his contacts and other than then maintenance it just doesn't get any better...
 
Status
Not open for further replies.

Users who are viewing this thread