New tank from Joyetech: Ultimo
- Thread starter Shawn Hoefer
- Start date
- th_trl_thread_readers 0
-
- Tags
- joyetech sub ohm coils tank
- Status
Oh wow. I don't get anything like that. That's no good!
I wonder if it's a problem with one of the O rings?Seeing ppl's comments having the same issue makes me doubt it an o-ring problem..
Will have to see what others say about their Ultimo.
Will have to see what others say about their Ultimo.
This is the first I hear about the leaking issue, thanks for bringing it up MSH69.
I've read all the comments on that video and it appears to be caused by the coils. It seems some of them don't align properly and you have to tinker with the ceramic part a bit until it is centered correctly & then there should be no leaking.
That's just from what people wrote in the comment section though, no hands on experience here just yet.
I've read all the comments on that video and it appears to be caused by the coils. It seems some of them don't align properly and you have to tinker with the ceramic part a bit until it is centered correctly & then there should be no leaking.
That's just from what people wrote in the comment section though, no hands on experience here just yet.
The one I have in now is a little off center. I didn't muck with it, but I will keep an eye on it.
Good to know! I will be on the lookout for that with these coils. I already replaced my first one and I want to clean it up and check it out to see how the ceramic is holding up and whatnot just out of general curiosity and I will see if I can manipulate the ceramic at all. I just heard of someone else who got some leakage when his tank got low and I will mention this to him.
The one that came with my Ultimo is also off center. I just looked at it. Interestingly, I haven't even had any condensation from the new coil I put in yesterday. When this tank of juice is gone I will check this coil and see if it is centered better than the first one was.
Forgot to post this here as well...
At 60W the tank gets quite warm so i put the heat sink in line, problem solved.
At 60W the tank gets quite warm so i put the heat sink in line, problem solved.
Forgot to post this here as well...
At 60W the tank gets quite warm so i put the heat sink in line, problem solved.
excuse my question, but what do u mean by "put the heat sink in line" ?
sry,, rookie here
I put one of these between the Ultimo and the Pico, it keeps the heat away from the mod.excuse my question, but what do u mean by "put the heat sink in line" ?
sry,, rookie here
$3.43 Kepler 510 Finned Heat Sink for Atomizers - stainless steel / 22mm diameter at FastTech - Worldwide Free Shipping
Just got my Ultimo in, I just bought it because I thought it's the perfect heigth for the XVo and Ystick and indeed it is....best fit of any atty so far.
Me being somewhere between MTL and DL I thought I would just use the RBA with it, however I first tried the Ceramic , I used it at "only" 40w with the AFC mostly closed off and it is certainly not bad.
I did get a lot off leakage the first time I used it.....was a bit bumped by it as most reviews state it is absolutely leak free. I did find out that you have to screw in the coils pretty tight, much tighter than I'm used to from other coils, that stopped the leaking for me.
Will try the RBA next to see how that goes......
and indeed it is....best fit of any atty so far.Me being somewhere between MTL and DL I thought I would just use the RBA with it, however I first tried the Ceramic , I used it at "only" 40w with the AFC mostly closed off and it is certainly not bad.
I did get a lot off leakage the first time I used it.....was a bit bumped by it as most reviews state it is absolutely leak free. I did find out that you have to screw in the coils pretty tight, much tighter than I'm used to from other coils, that stopped the leaking for me.
Will try the RBA next to see how that goes......
Just got my Ultimo in, I just bought it because I thought it's the perfect heigth for the XVo and Ystick
any chances of showing us a pic ? all the best with the RBA, let us know how it goes.
Just got my Ultimo in, I just bought it because I thought it's the perfect heigth for the XVo and Ystick
Me being somewhere between MTL and DL I thought I would just use the RBA with it, however I first tried the Ceramic , I used it at "only" 40w with the AFC mostly closed off and it is certainly not bad.
I did get a lot off leakage the first time I used it.....was a bit bumped by it as most reviews state it is absolutely leak free. I did find out that you have to screw in the coils pretty tight, much tighter than I'm used to from other coils, that stopped the leaking for me.
Will try the RBA next to see how that goes......
Oh man, you got one too already, hurry up mr. Postman!
I did read that you have to tighten the coil really tight when looking in to the leakage issue but forgot to post about it, glad you figured it out for yourself
Silver one, on a Dani..?
edit: You have an Athena Envy 22 as well, correct..?
Here is a pic off the silver one on a Dani, it's too big a tank for the Dani imo, as I like my tube's small. If you don't mind long tubes and use the 18650 configuration it's perhaps better a better match.
Dani also just goes to 40w, fine for me, but I think some want to use higher wattages with this tank.
and here in 18650 config next to my preffered Dani config
It's quite tall:
And it is absolutely no good fit for the Athena Envy 22:
You need pretty big tanks for the Athena, the Mutank is a very nice fit for that one.
- Status
Similar threads
- Locked
