- Status
My personal opinion... Don't buy any joyetech/wismec/eleaf products until they've been out a good long time. They have a habit of making their customers pay to beta test their mods.
Also, just about every joyetech/wismec mod I can think of for quite a while has had a janky 510. If you get a joyetech mod brand new, I'd say there's a good chance somethings wrong with the 510.
Also, just about every joyetech/wismec mod I can think of for quite a while has had a janky 510. If you get a joyetech mod brand new, I'd say there's a good chance somethings wrong with the 510.
My wife notices ALMOST all my new gear. I have sneaked in a few tho. She vapes but only uses an Eleaf Icare these days. She likes it simple.
All my Joyetech mods have been great... so far. I see a mod online and if I like the way it looks I will buy it. I'm very careful with all my mods except for one. That mod is the one that I'll use while doing yard work or working on my cars etc. It's a Sigieli mini 30W that miss-fires occasionally. Every Sigieli I've used has had early miss-fire problems.
All my Joyetech mods have been great... so far. I see a mod online and if I like the way it looks I will buy it. I'm very careful with all my mods except for one. That mod is the one that I'll use while doing yard work or working on my cars etc. It's a Sigieli mini 30W that miss-fires occasionally. Every Sigieli I've used has had early miss-fire problems.
For those wondering I've just seen a primo mini (coworker's) and it sits a merlin mini rta flush.
I can't see anything terrible with the 510, by looking at it anyway but this one seems to be working... Hopefully this one will be the one they get right on the first try.
I can't see anything terrible with the 510, by looking at it anyway but this one seems to be working... Hopefully this one will be the one they get right on the first try.
Has anyone here had experience with the Cthulhu MTL? I had a credit at GB burning a hole in my pocket so I used it to order one. I've been using a siren 22 for my mtl tank. It's been fine but I wanted to try something new. I read the thread on this tank and like every other tank, some people have no problems and others have flooding issues.
did a new build:
Black Nano
coil - 1 7 wraps 3.0 ID
material - 26/32 AWG A1 Kanthal Clapton
Ohms - .91
Watts - 23
Volts - 4.7
Temp -
AFC 1/4
juice Dinner Lady Rice Pudding 70/30
wicked just entering the juice holes
about 1/2 mm
measured the distance from the deck
to the top of the large air hole
comes in at .470"
set top of coil at .470" from deck
centered in between the juice holes
getting full flavor dense wet vape
Black Nano
coil - 1 7 wraps 3.0 ID
material - 26/32 AWG A1 Kanthal Clapton
Ohms - .91
Watts - 23
Volts - 4.7
Temp -
AFC 1/4
juice Dinner Lady Rice Pudding 70/30
wicked just entering the juice holes
about 1/2 mm
measured the distance from the deck
to the top of the large air hole
comes in at .470"
set top of coil at .470" from deck
centered in between the juice holes
getting full flavor dense wet vape
not sure but close to the top of the post holes
when i take it apart again i can give you a better answer
Care to take a pic of that build when you do? Trying to envision 17 wraps.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
coil 1 (7 wraps) sorry for the mis-understanding
don't think 17 wraps of a clapton coil would ever fit
That's what I was thinking. But some people pull off things I would never think to try
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
17 wraps according to steam engine it would Ohm out to 2.3 and
Heat capacity 85.88 mJ/K Ouch!
I alway have my heat flux set to about 200mW/mm²
and
52 W
← mod setting → 10.9V
mine won't do that higher voltage
It's OK, I've tried a lot of the "mtl" atties, most are dtl that can be adapted to mtl, the cthulhu like the merlin it has those inserts to adapt to mtl without sacrificing air velocity across the coil, but the chamber size and chimney diameter are too big for proper mtl.
Maybe try an ubertoot clone or gt3 with peek mtl insert, or a hussar with single coil deck and an mtl post. All of those do mtl very nicely.
This ubertoot has been my preferred mtl atty for a long time, and built like a tank so it'll probably last forever.
Last edited:
Just what I need another RDTA...
The Combo and Limitless Plus are working quite nicely for me, so I'll pass on the OBS version.
Now if there was an Aromamizer version out there... It would have to be snatched up ASAP.
#becauseSteamCrave
It's so new I couldn't find any vids on it. Just as well ha?Just what I need another RDTA...
The Combo and Limitless Plus are working quite nicely for me, so I'll pass on the OBS version.
Now if there was an Aromamizer version out there... It would have to be snatched up ASAP.
#becauseSteamCrave
I can't wait on the 25 version of the plusJust what I need another RDTA...
The Combo and Limitless Plus are working quite nicely for me, so I'll pass on the OBS version.
Now if there was an Aromamizer version out there... It would have to be snatched up ASAP.
#becauseSteamCrave
- Status
