Official GoodSense Vapor - i06DCA Beta Testing Results

[Panky]

Hey Jason, where ya been? Haven't seen any action around here in a while

 

[Panky]

I still can't believe these are still available Where did everyone go? Like I said in the IKV thread...

I am in shock that both colors are still available! Does nobody realize how amazing this invention is?! I am the owner of beta tester #1 and it is all I have been vaping with since I got it... Since then it has even been revised and I waited until the black ones came in to grab one of the newer versions. Trust me, if you use an i06 then you want one of these...

 

[Lax]

I still can't believe these are still available Where did everyone go? Like I said in the IKV thread...

They must have been restocked cause they were sold out yesterday.... But thanks for the heads up

 

[Panky]

They must have been restocked cause they were sold out yesterday.... But thanks for the heads up

Oh, I hadn't noticed that. I was just randomly checking to see if by chance they were still in stock and was very surprised

 

[Lax]

I could be wrong...it was really late Just glad to see the black available

 

[Ty89m]

So just received my i06 DCA today, and I notice I can't screw the top section down until it's flush with the bottom tube/connection. I can get it all the way down with my 306 DCA, so am curious if this is a problem? Anyone else notice this?

Thanks!

 

[Lax]

So just received my i06 DCA today, and I notice I can't screw the top section down until it's flush with the bottom tube/connection. I can get it all the way down with my 306 DCA, so am curious if this is a problem? Anyone else notice this?

Thanks!

The first i06 I used in the DCA I managed to get all the way down....only to rip it to shreds with a hammer to get back out I've since learned that lesson. I haven't had a i06 fit flush since, some are a little closer than others but I haven't been able to completely close the DCA on any. I'm still using a beta so I can't speak for the production models but sounds like that didn't change. YMMV.

 

[Ty89m]

The first i06 I used in the DCA I managed to get all the way down....only to rip it to shreds with a hammer to get back out I've since learned that lesson. I haven't had a i06 fit flush since, some are a little closer than others but I haven't been able to completely close the DCA on any. I'm still using a beta so I can't speak for the production models but sounds like that didn't change. YMMV.

It doesn't seem to matter much anyway. I can't really adjust the draw all that much though, which is fine as it's right where I like it, but have a lot more room to play when using my 306DCA. I do notice the pin won't protrude as far on the i06 DCA compared to my 306. Going to try it on the Provari to see if it'll make a connection. I do have spares (brass pin) for the 306, so might see how they compare in length to the one in the i06.

 

[andyman97]

As I missed out on the betas, I have a production model. I still have one of my first i06's from almost a year ago that I'm still using. It definitely doesn't sit flush. The draw is super tight, too. Doesn't really bother me because I still get great flavor and vapor. Haven't tried any of my new i06's in it yet.

 

[Ty89m]

Yup, mine still works great, just can't adjust the draw, which was a nice feature of the 306DCA. My main concern is leaking, and I have none, so the i06DCA is doing it's job nicely. The draw is fine for me as well, a bit tighter than what I usually like, but I'm used to it! Will have to try some of the newer i06's and see how they fit.

Side note, sure you all know this, but don't make the mistake I did and attempt to screw it down flush with the bottom piece. That top i06 was REALLY a pain to remove from the upper sleeve ha! Got it all taken care of though, lesson learned...the hard way.