Orion V2 roll call
- Thread starter tierrataz
- Start date
- th_trl_thread_readers 0
- Status
40mm in length and 70 mm in Width, i only use 40 mm Width, like a little hotter vapes
Just got some parts in, i was so scared of leaking so i put 4 rod o ring in there just to make sure.
By the way, I have tons of M2 nut, Rod O ring and Nylon insulator left, pm me if you need some so you don't have to buy 100 of them...
By the way, I have tons of M2 nut, Rod O ring and Nylon insulator left, pm me if you need some so you don't have to buy 100 of them...
I just picked up an Orion today and I'm loving it so far...these parts you speak of are obviously for the Orion, correct? Is it prone to get leaky? Or just just like any other atty with O rings, it's good to change them out every now and again?
Congrat!! Love my Orion as well, the flavor is just so damn intense.
Some earlier version of the Orion had issue with juice from the atty chamber leaked down to the switch and causing problem (not firing). But the new one has the silicon sleeve around the switch rod and solve the leaking issue.
The "rod o rings" that I mentioned is for the rod which also prevent leaking down to the switch. and yes they are for the Orion v2.1.
Some earlier version of the Orion had issue with juice from the atty chamber leaked down to the switch and causing problem (not firing). But the new one has the silicon sleeve around the switch rod and solve the leaking issue.
The "rod o rings" that I mentioned is for the rod which also prevent leaking down to the switch. and yes they are for the Orion v2.1.
Last edited:
Just experimented 28g, 7/8 wraps at 1.2 ohm and it is AMAZING!!!!
Last edited:
new great setup, even more flavor!!!!!
500# 30 mm x 40 mm with Ribbon flat Kanthal 0.20 AWG 4/5 wraps at 1.2 ohm.
you can get the wire here:
Ribbon 020X 004" 10' 5X 1mm 3M Heating Flat Wire | eBay
500# 30 mm x 40 mm with Ribbon flat Kanthal 0.20 AWG 4/5 wraps at 1.2 ohm.
you can get the wire here:
Ribbon 020X 004" 10' 5X 1mm 3M Heating Flat Wire | eBay
""After watching this video...I decided to try it out....and let me say that I am now a believer!!!...WOW ED!!! How using 500 mesh makes a whole world of difference. Rolled up a tight 70mm length 500 mesh wick...3 coils of 30 awg kanthal wire on my Orion V2.1...Vaping bliss!!! Tons of flavor and vapor!!! Thank you so much Ed for posting this video...I think I just found my new setup for all my rebuildables!!!
To everyone watching emonty's video or reading this post....YOU MUST TRY THIS!!! You will not regret it!!! ""
Where is this video that is mentioned on this post? i'm trying to find the post but not able to do so. Any help?
To everyone watching emonty's video or reading this post....YOU MUST TRY THIS!!! You will not regret it!!! ""
Where is this video that is mentioned on this post? i'm trying to find the post but not able to do so. Any help?
lol,happy you found it
here is my youtube channel. Not a lot to see but it is there
https://www.youtube.com/user/emonty999
lol,happy you found it
here is my youtube channel. Not a lot to see but it is there
https://www.youtube.com/user/emonty999
Thanks emonty, lol
can someone tell me if this are the correct orings for the orion as this are the items i'm about to order:
Buna-N Tank Orings - 12mm ID with 1.5mm x-section - $5.72 for 100
Buna-N Switch Rod Orings - 2mm ID with 1mm x-section - $4.38 for 100
And for the Nylon Shoulder Washer - Long Barrel - 6/6 No. 2 - $4.68 for 100 , i see 3 results... which is the correct size? It's so confusing lol.
Buna-N Tank Orings - 12mm ID with 1.5mm x-section - $5.72 for 100
Buna-N Switch Rod Orings - 2mm ID with 1mm x-section - $4.38 for 100
And for the Nylon Shoulder Washer - Long Barrel - 6/6 No. 2 - $4.68 for 100 , i see 3 results... which is the correct size? It's so confusing lol.
They is a post by me several pages back that had the dimensions. Search for posts by crack3done. It was wel over a month ago if not almost two.
Sent from my Samsung S III running on SS mesh and kanthal.
Sent from my Samsung S III running on SS mesh and kanthal.
Hi this was from your previous post but when i search for them on the website i got this results and would want to make sure they are the correct ones as it'll take atleast 10-15 days to reach me and if i'm wrong i would need to re-order and wait another 10-15 days lol. And also that website is difficult for someone like me who has no idea what i'm searching for
If you could look at the pics and verify if those are the right one i would appreciate it ...
http://www.e-cigarette-forum.com/forum/apv-discussion/280573-orion-v2-roll-call-243.html#post7854925
Here's the link
You can try Element14, they have the spare m2 nuts and they come in pack of 100s
Here's the link
You can try Element14, they have the spare m2 nuts and they come in pack of 100s
Here is the link for all the dim
http://www.e-cigarette-forum.com/fo...29-orion-v2-v2-1-care-package-full-co-op.html
http://www.e-cigarette-forum.com/fo...29-orion-v2-v2-1-care-package-full-co-op.html
can someone tell me if this are the correct orings for the orion as this are the items i'm about to order:
Buna-N Tank Orings - 12mm ID with 1.5mm x-section - $5.72 for 100
Buna-N Switch Rod Orings - 2mm ID with 1mm x-section - $4.38 for 100
And for the Nylon Shoulder Washer - Long Barrel - 6/6 No. 2 - $4.68 for 100 , i see 3 results... which is the correct size? It's so confusing lol.
- Status
Similar threads
