Orion V2 roll call
- Thread starter tierrataz
- Start date
- th_trl_thread_readers 0
- Status
thanks lexi, it gets a little tricky understanding what les is trying to say sometimes..
I know what ya mean. I spend time in a German forum, I often completely mistranslate stuff.
Btw. I've been using genenis attys for a long time now. Dare I say, perfected it. I just did the JackFrost oxidize method.. Friggin awesome!
Cut a piece of mesh, burn it, roll it, done!
No quenching, no burning juice.
I just set up 4 attys this way. Not even the slightest short. Prefect wicking.
Btw. I've been using genenis attys for a long time now. Dare I say, perfected it. I just did the JackFrost oxidize method.. Friggin awesome!
Cut a piece of mesh, burn it, roll it, done!
No quenching, no burning juice.
I just set up 4 attys this way. Not even the slightest short. Prefect wicking.
I understood the same. 357 sounds like the new cut off till fall. It also is dependent on Pailpoe being willing to produce the pcb/switch. Being there from almost the start, it's mind blowing how the V2 & V2.1 have taken off. I know he wants to work on other things too. I'm anxious to see what will be next.
I've finally decided to put my name on that list for the orion. If I didn't drag my feet I would be almost 100 spots up on the list but looks like I got in just under the cutoff.
Congrats! I know, its going to be 400 in a week or less.
He will announce a day or two ahead that he is sending notices out and the time. He has on the past given the numbers that are ready. These are built & ready to go, so little wait.
Last release, about 25 did not respond back so be prepared if you are just below the cut off.
I lusted after a Orion since Feb and gave up when I scored a Zen.
But I'm back in the saddle with slot #330! And Viper is going trade me his for my Zen Std.
I'll have two Orions and two Zens.
Exciting.
But I'm back in the saddle with slot #330! And Viper is going trade me his for my Zen Std.
I'll have two Orions and two Zens.
Exciting.
Hey gang. I see a lot of familiar names on the list. Looks like a lot of Orion's will hit the US this summer.
. What do you think about putting together a tips/tricks post that could be tagged & bumped as needed?
. What do you think about putting together a tips/tricks post that could be tagged & bumped as needed?
Just got mine today.
A very beautifully put together device indeed.
This is a great idea. I already have a ton of questions.
Super easy.
I have a hard time finding information in a big forum thread. Take the HOH thread for example. Fahgettaboudit!
The only downside is that it would be yet another website to bookmark and remember.
Any way, I could do it. And members could make changes and add topics.
And it won't be super purtty. lol
Ask away. I'm sure we can get you sorted.
My 2 best tips for easy set up.
1- tighten the top terminal nut till 1-2 threads show above the nut. Helps eliminate hot spots there.
2- with a pair of needle nose, bend the edge of the bottom washer down and the top washer up. This will save frustration in wrapping. Forms a nice. "gutter" the wire will drop into.
Congrats!
My 2 best tips for easy set up.
1- tighten the top terminal nut till 1-2 threads show above the nut. Helps eliminate hot spots there.
2- with a pair of needle nose, bend the edge of the bottom washer down and the top washer up. This will save frustration in wrapping. Forms a nice. "gutter" the wire will drop into.
Congrats!
Putty smurty! Info in one tidy spot is all peeps need. Been on a number of threads where finding the pearls is just ....
Go for it! ......and thanks!!!
Go for it! ......and thanks!!!
Super easy.
I have a hard time finding information in a big forum thread. Take the HOH thread for example. Fahgettaboudit!
The only downside is that it would be yet another website to bookmark and remember.
Any way, I could do it. And members could make changes and add topics.
And it won't be super purtty. lol
1) what is the small washer for?
I'm guessing this goes on the threads on the device to help line the hole up with the wick? Otherwise mine does not line up.
Did most of you open up the air hold for more airflow?
Is it normal for the cap to get really hot?
I'm guessing this goes on the threads on the device to help line the hole up with the wick? Otherwise mine does not line up.
Did most of you open up the air hold for more airflow?
Is it normal for the cap to get really hot?
1-if you mean o ring, correct. Most of us sand our tanks so the intake lines up with the wick.
Some have enlarged the inlet. I would caution you to use it for a week to be sure you want to. Les has said there will be no replacement caps. He even made a video showing how to mod a juice bottle for testing before commiting to drill.
If you chain vape, yes. Make sure the wick is not too tall.
Some have enlarged the inlet. I would caution you to use it for a week to be sure you want to. Les has said there will be no replacement caps. He even made a video showing how to mod a juice bottle for testing before commiting to drill.
If you chain vape, yes. Make sure the wick is not too tall.
Is there a video or precise instructions anywhere talking about how or how much to sand the tank or enlarge the hole?
And yes sorry o-ring.
I just push the small piece down while wrapping the wire around the screw.
Not that I'm aware of for either.
Sanding is pretty straight forward. Just keep checking as surely once you get going too fast you will over shoot the wick!
Others will have to chime in on the drilling . I've not done it.
Sanding is pretty straight forward. Just keep checking as surely once you get going too fast you will over shoot the wick!
Others will have to chime in on the drilling . I've not done it.
For what its worth, I did not see any improvement in a larger inlet hole. I know there are many more experienced people out there that say it increases the amount of vapor but I personally did not see any improvement.
- Status
Similar threads
