Penelope V2

[D Stanley Querfurth]

if we want to have a drip option we have to make thin mouthpieces Stan. Exactly like atomizers. Atomizers have 8,65 hole and 9mm outside diameter. That way, drip tip and GG mouthpiece will have exactly the same diameter outside

We can make thicker mouthpieces of course. The maximum we can go is at 10mm. Its not a small amount of thickness for Steel. But I dont know if they will look nice with an 9mm drip tip on it

Round off the ends of the stronger mouthpiece vor DT's like at the ends from normal mouthpice. Would look nice.

LIKE SHAKE SAYD; THEN MAKE A RIGHT DRIP TIP FOR PENNY; A GG ONE !!!

AND IF YOU MEAN A STRONGER MOUTHPIECE FOR ITHAKA--LOOK AT MY SETUPS´S: THE MOUTPIECE DOESN´T REACH OUTOFF iTHAKA IN LONG mod !!!

YOUR WORK WILL LAST FOR LIFETIME PLEASE LET THE DT OPTION GET THE SAME LIFELINE !!!

GOOD NIGHT

STAN

 

[yankeebobo]

What about a GG drip tip I feel odd putting something no GG on a GG


Sent from: The Land of Tortuga!

But Shak, the very point of a universal drip tip is the fact that you can use any drip tip. I would think that if we want a GG drip tip, you have either an adjustable tip (included) or maybe a one piece mouthpiece.

 

[D Stanley Querfurth]

But Shak, the very point of a universal drip tip is the fact that you can use any drip tip. I would think that if we want a GG drip tip, you have either an adjustable tip (included) or maybe a one piece mouthpiece.

I can put any atty on gg . And every gg atty on other mods. Why Not make a gg drip tip ?

Stan

P.s. still found no driptip reaching gg quality. Or Not much.

Gesendet von meinem HTC Sensation XE with Beats Audio Z715e mit Tapatalk

 

[LongDraw]

So I am torn.

Just got the peny v2 in the mail and cleaned it up. First thing I did was put the rebuildable part in and noticed as others the center post was off. Didn't want to fiddle with and risk bending/breaking anything so i adjusted the plastic bit that separates the positive post from the housing and this allowed the post to be pretty much straight.

Then I cleaned up the peny v2. I think I really like the thicker metal and added heft of the peny v1 and ody. Kinda like with the ithaka I get nervous how well the tank part will hold up, no I am not hercules but peny v1 and ody tanks are thick.

Built a 1.4 - 1.5 ohm coil, just like i use on peny v1, ody, ithaka. The draw is really airy compared to what I am used to. I put it on a provari and on just gg. On the just gg I changed the AFC of JGG and if any air comes through it seems to be airy. I played with the adjustable drip tip (up, down, round in circles, changed the oring) and still just really airy. I then put on 2 different drip tips (1 regular and now using shorty drip tip) and still pretty airy.

My juice is 65pg and 35vg. I don't seem to get as big of clouds as compared to the other gg atties at times. Not sure if my wick is just not keeping up, used 3.5 mm at the coil and removed 3 strands from each channel, opened up the mouthpiece 1.5 to 2 full turns.

Gonna keep vaping on the tank, filled it so will have some time to adjust my draw and everything else.

Any suggestions on how to tighten up the draw would be welcomed, thats my main concern.

 

[yankeebobo]

I can put any atty on gg . And every gg atty on other mods. Why Not make a gg drip tip ?

Stan

P.s. still found no driptip reaching gg quality. Or Not much.

Gesendet von meinem HTC Sensation XE with Beats Audio Z715e mit Tapatalk

I guess my point is regardless if imeo makes a GG drip tip or not, the walls would be thin and possible damage.
If Imeo makes a drip top, I'd rather a GG full mp than a GG tip. There are plenty of good quality basic tips already. A GG mp would also serve to strengthen the mp

 

[yankeebobo]

Imeo would it be possible to use a stronger grade SS on the mp of the penny? This would still allow all features but be stronger.

 

[yankeebobo]

Long, you changed one of the orings to the other that was supplied. And then you still closed the adj air tip and it's still loose?
Close that tip all the way and take a draw. Still loose closed?

I found it to be completely opposite. I'd ipen and it was still tighter. No adj tip or straight universal drip tip to me was slightly airier than v1

Also. If your missing clouds, close the juice and vape it. You may have actually over wicked?

 

[LongDraw]

Well with the shorty drip tip the clouds are back, switched back to then peny v2 tip and they reduce. I tried pushing the peny v2 tip down more but doesn't seem to go any further.

For the peny v2 tip it seems to take away the heat, plus lessen the vapor production for me. This seemed to happen with the two small orings, and then the same deal when i replaced the bottom oring with the larger one.

With the shorty drip tip I am beginning to enjoy the peny v2, would like to figure out the issue with the peny v2 tip though.

Does you peny v2 tip actually sit flush to the drip tip mouthpiece?

Long, you changed one of the orings to the other that was supplied. And then you still closed the adj air tip and it's still loose?
Close that tip all the way and take a draw. Still loose closed?

I found it to be completely opposite. I'd ipen and it was still tighter. No adj tip or straight universal drip tip to me was slightly airier than v1

Also. If your missing clouds, close the juice and vape it. You may have actually over wicked?

 

[yankeebobo]

The tip pushes in until it can't go any further then screws into the MP. Notice on the right it's fully screwed in. You should get NO air in this position.

 

[dutch onsea]

A hard crowd to please? nah, me too Imeo I want you to design a new mouthpiece that doesn't bend wen I drop it. No serious, just made this new setup 1.2 ohm microcoil with cotton around it. what the hell!!! Most awesome vape
thanks Imeo

 

[yankeebobo]

I think what also needs to be considered for the record is the channel inside the mouthpiece. The iatty had a spectacular vaping experience and it was due to the narrow channel of the cone. The Penelope mp on the v2 narrows the channel in similar fashion. This forces the vapor more enhancing it.

 

[LongDraw]

Well I'll be a monkeys uncle, the thing does screw in, I was trying to push

So I can make it have no draw now, thanks yankee. Gonna have to play around with it some more, that piece still seems to take away the heat and some of the vapor with what I am doing at the moment. Don't get me wrong, nice looking, just to use to the other attys. Hopefully it grows on me more.

The tip pushes in until it can't go any further then screws into the MP. Notice on the right it's fully screwed in. You should get NO air in this position.

 

[yankeebobo]

That tip is still a question mark for me. I find any tighter on the draw is changing the flavor on the wrong direction. So I vape with it wide open or a universal tip. But I'm used to v1 which is pretty loose on the draw.
But now you have variations to vape with.

 

[Aal_]

The penny v2 mouthpiece's walls are same thickness as a regular atomizer? So what makes it bend is actually the weight of Penny? Atomizers are light and don't bend when they fall down. It makes sense, but I think we need a solution. At least not for it to bend while changing a lot of mouthpieces like what happened with Stan.

 

[Shaketuga]

But Shak, the very point of a universal drip tip is the fact that you can use any drip tip. I would think that if we want a GG drip tip, you have either an adjustable tip (included) or maybe a one piece mouthpiece.

I just think it would be sweet to have one with either GG or the wings on it lol I know it sounds silly but would look bdass


Sent from: The Land of Tortuga!

 

[firehorse66]

I am very glad reading your comments Fire, keep vapinggg buddy

I am now already at 9 mg of nicotine and close changing to 6 mg according to my Liquid stock.
However thanks you and GG I'm almost certain that I will be vaping even without nicotine.

I wish you and your family a Merry and blessed Christmas!!!

 

[D Stanley Querfurth]

 

[Itshak]

I'll add this for my next order of spare parts,
After we will have spare parts for Ithaka new rebuildable part as well.

 

[blackwater]

Still no V2 in my box. So bummed that I can't play along with you guys.

 

[Lo zio]

sure Lo zio, thats not difficult. But having a drip tip option is not a bad thing. I understand that you are not happy with what happened to you but if there was a drip tip or AD control inside mouthpiece, this wouldnt have happened

Of course.
The point is that with its own tip I really couldn't vape Penny V2 - it mutes flavour, it gets too airy. This is just a matter of taste, I know, but I try to adjust my devices to my own. With other tips yes, it got better, but still not comparable to the configuration without tip. So if this is the case, I would prefer a regular one piece mouthpiece as V1 has, since I do not like the rendition of the new tip and actually I am not intersted in mounting any other particular tip, I love the look and feel of GG mouthpieces.
This is why I would like to know if you plan to produce one; if yes fine, I'm in, if not... well I should buy a new standard mouthpiece soon with the risk of damaging it again sometime in the future, and I don't know if I like this option, maybe I will just sell my V2 and stick two my two V1. Even if it would be a shame, since V2 actually vapes great - without tip at least.