Phiniac and Siam Mods Cobra Rebuildable Atty

Status
Not open for further replies.

moorea

Unregistered Supplier
ECF Veteran
Aug 11, 2009
6,868
7,355
55
Marion, MT
phiniac.com
I believe Moo thought she was opening a thread to announce the Cobra. What she got now is a full support thread. :)

Support is good! Keep it coming, I can't post in threads other then my own and at some point I am going to have to figure out how to use my Cobra, so I appreciate all the support offered here!
 

moorea

Unregistered Supplier
ECF Veteran
Aug 11, 2009
6,868
7,355
55
Marion, MT
phiniac.com
Aren't all the Cobras sold out?

The Cobras are, but I have a pile of Cobra glass here that is just waiting to be sandblasted and sent to it's new home! I keep telling each piece in the pile it will have a new home soon so it doesn't get too depressed and feel homeless!
 

tmcase

ECF Guru
ECF Veteran
Verified Member
Apr 20, 2011
20,862
54,652
The Cobras are, but I have a pile of Cobra glass here that is just waiting to be sandblasted and sent to it's new home! I keep telling each piece in the pile it will have a new home soon so it doesn't get too depressed and feel homeless!

Well what good is a cobra glass without a cobra?:facepalm:
 

tmcase

ECF Guru
ECF Veteran
Verified Member
Apr 20, 2011
20,862
54,652
I just tried the tight wick with 400 mesh and tight in the wick hole. I torched the unrolled mesh to death but didn't do the juice burn and quench because I just couldn't believe that wouldn't short and not fire at all. But it worked and I'm getting tons of vapor but no flavor, in fact it's still not wicking so I get a couple of hot spots. When I put juice on the wick and fire it up it looks like a chimney and snap, crackles and pops but when the juice dries up a couple of coils start glowing. IT'S NOT WICKING!!!!! :mad:

Again, this is not a cobra but a DID knockoff. Same principle though.
 

yankeebobo

Vaping Master
ECF Veteran
Verified Member
Jun 23, 2012
7,046
21,034
Western MA
I just tried the tight wick with 400 mesh and tight in the wick hole. I torched the unrolled mesh to death but didn't do the juice burn and quench because I just couldn't believe that wouldn't short and not fire at all. But it worked and I'm getting tons of vapor but no flavor, in fact it's still not wicking so I get a couple of hot spots. When I put juice on the wick and fire it up it looks like a chimney and snap, crackles and pops but when the juice dries up a couple of coils start glowing. IT'S NOT WICKING!!!!! :mad:

Again, this is not a cobra but a DID knockoff. Same principle though.

Fill screw out?
Pull it out and give it one torch and quench on the top half where coils go. I didn't torch it much before rolling. I touched it to orange. Not red. I know some don't do the quench, but I seem to need one or two. Seasoning will bring flavor on. So as you vape with juice, it will come through
 

tmcase

ECF Guru
ECF Veteran
Verified Member
Apr 20, 2011
20,862
54,652
Fill screw out?
Pull it out and give it one torch and quench on the top half where coils go. I didn't torch it much before rolling. I touched it to orange. Not red. I know some don't do the quench, but I seem to need one or two. Seasoning will bring flavor on. So as you vape with juice, it will come through

I had the fill screw out. :( The flavor loss may be due to not juice, burn, quench but the only time there isn't any flavor is when it isn't burning my throat. :mad: It even flamed once when I had the top off. Actually caught on fire. :-x
 
Status
Not open for further replies.

Users who are viewing this thread