order 3179 here! I did'nt get a notice of shipment so Im guessing they finished up today just short of my order.
- Status
mwa or anyone tech orientated is there a reason that the Provari wouldn't work with a HR MAP tank at 3.2?
I am still waiting on mine #3233 and I'm not mechanically/electrically inclined so I'm curious.
C.B.
It would be no problem at all! I use the 2ml Clear E2 mod with at 3.2Ω and find, for me, the perfect setting is 4.0v. Cigarbabe ....you're going to just love it!
I have a vault full of the newer Mini 2ohm and HV-801's Jimho, dialing in the 2ohm Mini 801 between 4.0v-4.2v is the absolute best. As for the HV I love it @ 7.4 with two stacked AW 3.7 123A's on another mod best, there awesome like this, fill em up to the bridge and vape vape vape, but using the Mini 2 ohm 801 on the Provari is indeed a treat !
Actually, it does. I bought 2 AW IMR 18650 batts with my ProVari order and it's happening with both batts. The batt voltage gets to 3.5-3.6 and the ProVari won't vape. It's happened several times now. It doesn't happen all the time but enough to make me wonder what's going on. I remove and re-insert the batt and then it vapes again.
When it happens I check Cb and it won't read the volts. The display shuts off with Cb still showing. When I remove and re-insert the batt the ProVari will vape again. I then check the Cb and the volts read 3.5 or 3.6. I haven't changed vaping voltage or my carto. Sometimes it just goes dead til I remove and re-insert the batt and sometimes it will go all the way to the 3.4 volt cutoff and the button flashes red.
Other than that, the ProVari is working aok.
I also have found a use for all the old but new HV901's I had sitting around resistances between 4.2-4.9, these are running excelent on my provari running a drip tip and dripping into these and vaping away, nice vape at the higher voltage settings
lol! and here i thought we were in the 3300's almost to 34. good to hear tho! and ty for working so hard on getting everything out! must be hellA few more units have shipped out and we are now on the edge of going into the 3200's. Yesterday was only a small sprinkle, were getting another larger batch of boards on Friday and well work the weekend to get them tested and out the door.
Last edited:
Sweet!
Maybe mine is within sight at #3233.
I'll praying to the provape gods tonight! Huzzah!
Thanks again Pete and Ren for the info on atty's.
C.B.
Last edited:
with the Provari and 2.2 Ohm i don't anticipate the need for a big stash of attys... a joye reg 510 or a Titan 510 runs a nice range of vapes from 4v down to 3.4 or 3 .5 for a mild yet full vape (depending on the juice and the mood).
with the Provari you can dial in by .1 degree up or down, to get it just right for those factors (juice/ mood)
i figure this info is good for newbs who want to start their vape careers with first rate equipt.
I have a bunch of different attys and cartos even, from my 4 or 5 nonths in the ecig realm... darting here and there, thinking one pv would be "it" and stock up on the accessories, then another and another... ha
with the provari, i can get the best/better out of each !!! who'd of thought one PV could do it all...
i do have some higher resistance attys lined up just for Pro vari as well... heheh
...thanks to jimho; for pointing me here (and earlier, to that one other non vv pv that i can't do without now)... i am so satisfied.
with the Provari you can dial in by .1 degree up or down, to get it just right for those factors (juice/ mood)
i figure this info is good for newbs who want to start their vape careers with first rate equipt.
I have a bunch of different attys and cartos even, from my 4 or 5 nonths in the ecig realm... darting here and there, thinking one pv would be "it" and stock up on the accessories, then another and another... ha
with the provari, i can get the best/better out of each !!! who'd of thought one PV could do it all...
i do have some higher resistance attys lined up just for Pro vari as well... heheh
...thanks to jimho; for pointing me here (and earlier, to that one other non vv pv that i can't do without now)... i am so satisfied.
Last edited:
Provari 2965 just arrived First impressions are real quality and first try is awsome, the settings and possibilities are endless.Will post up my thoughts with a mini review later.That is if I dont make myself ill with too much nic
I've had that happen once when pulsing with a 1.7 atty- turned out it was an intermittently shorting center post - It was a cheapie and had lots of use - wouldn't be surprised if I had overtightened it at some point in its life ...I didn't bother disecting it, just tossed it in my dead atty draw. Hasn't happened again.
A few more units have shipped out and we are now on the edge of going into the 3200's. Yesterday was only a small sprinkle, were getting another larger batch of boards on Friday and well work the weekend to get them tested and out the door.
Maybe I'll get mine next week!
Morning all
ya know using this Provari is almost better than SEX. I said ALMOST......
God help me for saying this. OK let the comments begin. lolol
Happy Provari day to all. I am off to the VA for few hrs. c ya
i made this comment cause i want to see some of the comments lol.
ya know using this Provari is almost better than SEX. I said ALMOST......
God help me for saying this. OK let the comments begin. lolol
Happy Provari day to all. I am off to the VA for few hrs. c ya
i made this comment cause i want to see some of the comments lol.
I think you were being serious
and then I feel very, very sorry for you....
you can joke that in ways they are similiar...
atleast you can read the provape
never quite satisfying enough
it tells you how much its gonna put out
always push the red button
ok I'm done...
I agree - I run the 801's a bit higher ... actually sitting here with a 3.2 801 running at 5.9V.... whereas I tend to run a bit cooler with 510's - I've stacked to get 7.4 also with 4.5 ohm attys- too hot for most of my juice and way unstable...
.... I need to get some of those mini's though- I just have too many attys sitting around .... are they really that different than the semi's? I was thinking of cutting down one of my 801's with a tube cutter to see if it makes a difference.
Vape on the ProVari WHILE having sex!
Problem solved.
I bet that makes it better!
for some...
Bassthumper Pete and monter kenny
i am laughing my .... off. i knew i would get a few comments. Pete your idea is best. c ya at the meet. save me a seat. bringing Provari and something else.
i am laughing my .... off. i knew i would get a few comments. Pete your idea is best. c ya at the meet. save me a seat. bringing Provari and something else.
don't know if it's just me, but my mini lr 801 got clogged up too soon.... hard draw.
but this is on another 3.7v pv... maybe cranking it up on the Provari will clear it out some...
but this is on another 3.7v pv... maybe cranking it up on the Provari will clear it out some...
I bet that makes it better!
Speaking from experience are we Pete,MonsterKenny?
Sounds awesome!
C.B.
- Status
