I am just trying to see if this works.
I am trying out Imgur as a Pic host, It looks like a good one I can arrange pics into folders and, have them set to private, I am not sure I want these public.
KAS
I just want to note, that if you open the pic in new window you can zoom in on them
It's not hard to do. The top plate of the 510 is press fit and will pop off if not careful when replacing the o ring but it's easy to pop off the top cap if you need to. I've done it and if I have to again I should make a vid of it.
What tool did you use?
but didn't you mention you had to remove the whole top plate of the Radius in the process?
this is what you said:
"The pin is actually two pieces. The contact plate is press fit onto a smaller pin that goes through the top cap. If you pull to hard or pry against the side too hard you can pop the contact plate off. If that happens you will most likely have to pull the board carrier and top cap out to fit it back together. Since the pin floats, there's an insulator on the pin shaft that the contact plate will hit before it's completely pressed on."
Thanks Kas!!!Sense you asked, here is most of them,
And my P67.
KAS
I see two brass mini's in there!Sense you asked, here is most of them,
KAS
Very nice. Just looking at mine and it's taken on a nice mellow gold tone to it, I decided to just let it patina with use and time rather than shining it up from time to time. You must really like them Chalice atties?!
I see two brass mini's in there!
I have let my tumbled brass do as it wish's as far as patina, but my shiny one is still shiny. Yep I do like the chalice's I have 10 of them, all authentic's. I also have 2 of the little 0-16's, and 4 nuppins. I stocked up on the chalices from the start, I knew I liked it so I got one for each of my REO's. There are so many that are geared to dual coils and low ohm's, that it could make your head spin. I do have the Nuppin still on my P67 though also very good, I was able to get the air flow dialed way down on it to where I like it.
KAS
I am just trying to see if this works.
If you only have one or two of each, go for it. But, with an entire collection of one kind, it deserves special treatment. You're photo is beautiful!That will be in another folder, I am just starting to upload pics to the site. I think at some point I will take a pic of all my mod's in one pic, I have never done that.
KAS
I'm waiting to hear what folks say about the Calice V3 clone, maybe I'll try one of them to see how I like it. Early on I took a liking to the Cyclone atties and RM2's so got a bunch of those, and I do like the IGO-W atties with single coil. Also got some Loki lab Odin BF atties in the mix, them things are built like tanks lol. I think my favorite small chamber attie is the Hornet, got two of them and they will never leave the house.I have let my tumbled brass do as it wish's as far as patina, but my shiny one is still shiny. Yep I do like the chalice's I have 10 of them, all authentic's. I also have 2 of the little 0-16's, and 4 nuppins. I stocked up on the chalices from the start, I knew I liked it so I got one for each of my REO's. There are so many that are geared to dual coils and low ohm's, that it could make your head spin. I do have the Nuppin still on my P67 though also very good, I was able to get the air flow dialed way down on it to where I like it.
KAS
Lately I've picked up a few more of the 2.1 18490 mini's, they fit pretty good in the pocket, and the batteries hold up better under chain vaping then them little 14500's do. We're all nuts in here
AMEN!!!We're all nuts in here
I'm waiting to hear what folks say about the Calice V3 clone, maybe I'll try one of them to see how I like it. Early on I took a liking to the Cyclone atties and RM2's so got a bunch of those, and I do like the IGO-W atties with single coil. Also got some Loki lab Odin BF atties in the mix, them things are built like tanks lol. I think my favorite small chamber attie is the Hornet, got two of them and they will never leave the house.
Lately I've picked up a few more of the 2.1 18490 mini's, they fit pretty good in the pocket, and the batteries hold up better under chain vaping then them little 14500's do. We're all nuts in here
Do you mean the new Chalice IV (4)? I am curious about that one, all of mine are III's (3's). I forgot about the Cyclone I do have one of those as well. I never had the IGO's, and the loki Labs Odin seemed like it was geared towards dual coils and too much air flow, so I stayed away from it. For some reason building on the Cyclone was just weird for me, I mean it worked, but the way you had to wick it was just odd.
KAS
Thanks
I have always grouped my pics together this way, with each brand that I own, IE : provari's, REO's, and Billet Box's. It would be a bit of a challenge to get them all in one picture, that shows the unique quality of each, but I like the idea.KAS
Yeah, you got to leave one side of the wick short in them Cyclones, but it works just fine. The Odins have an offset cutout for single coil, but I do believe they are better suited for duals, I plan to dig one out and shoot for a dual setup around .9 ohm.Do you mean the new Chalice IV (4)? I am curious about that one, all of mine are III's (3's). I forgot about the Cyclone I do have one of those as well. I never had the IGO's, and the loki Labs Odin seemed like it was geared towards dual coils and too much air flow, so I stayed away from it. For some reason building on the Cyclone was just weird for me, I mean it worked, but the way you had to wick it was just odd.
KAS
Boy it sure is gettin dark over here!!!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I was sorry to see Loki Lab's go away, I kind of thought about getting one of those for a long time. I still have several of his carto tanks that I used my Sophia's in, they were a very nice tank. I think a few are in my Provari group shot.
KAS
Boy it sure is gettin dark over here!!!
Sent from my iPhone using Tapatalk
Found the light switch...
Sent from my iPhone using Tapatalk
Me too, I liked their stubby SS drip tips, last order I got they were five bucks each, and they threw in a couple extras. Nice folks to deal with, once I needed a screw for an Odin Deck and they sent me a couple no charge. They will be missed...
Similar threads
- Locked
- Locked
