ProVarinati Diner & Saloon and Beyond

[kas122461]

Me too, I liked their stubby SS drip tips, last order I got they were five bucks each, and they threw in a couple extras. Nice folks to deal with, once I needed a screw for an Odin Deck and they sent me a couple no charge. They will be missed...

I think I read somewhere that they can still be reached threw face book, but sense I don't do face book I will never know.

KAS

 

[ENAUD]

Boy it sure is gettin dark over here!!!

Sent from my iPhone using Tapatalk

Those are awesome for when roasting marshmallows by the fire!

 

[ENAUD]

I think I read somewhere that they can still be reached threw face book, but sense I don't do face book I will never know.

KAS

I always got the feeling their stuff was a side business, because the machining on everything was so perfect. I haven't ever bought anything on FB, just seems kind of weird to me the way some things go on there...

 

[TraderX]

Just added another log to the FYR!!!

LOLz

There is an Astroturf over on ebay unloading a boat load of Provari mods recently. I think maybe I have solved the meaning of the logs on the fire mystery

 

[AstroTurf]

There is an Astroturf over on ebay unloading a boat load of Provari mods recently. I think maybe I have solved the meaning of the logs on the fire mystery

No Way...

LOLz

 

[jwbnyc]

I thought maybe he was burning his cow chips...

 

[Hobbs]

Made everybody think. Mason thought about Schrodinger's cat ... or maybe bacon

 

[coldgin96]

Made everybody think. Mason thought about Schrodinger's cat ... or maybe bacon

The statue guy is trying to remember where he put his clothes.

 

[Ca Ike]

What tool did you use?

I used a drift punch and a small plastic faced body hammer. To remove the top cap on my P3. Use an old kayfun clone base to hold the contact in place once I got the insulator back on and a mini c-clamp vise grip as a press.

but didn't you mention you had to remove the whole top plate of the Radius in the process?

this is what you said:
"The pin is actually two pieces. The contact plate is press fit onto a smaller pin that goes through the top cap. If you pull to hard or pry against the side too hard you can pop the contact plate off. If that happens you will most likely have to pull the board carrier and top cap out to fit it back together. Since the pin floats, there's an insulator on the pin shaft that the contact plate will hit before it's completely pressed on."

The radius is done different than the p3/classic/Ti line. I've taken the top plate off my radius but just out of curiosity not to fix anything. The pin on the radius is not part of the board but has a wire soldered to it. Should be the same two piece pin though.

 

[Katdarling]

I am just trying to see if this works.



I am trying out Imgur as a Pic host, It looks like a good one I can arrange pics into folders and, have them set to private, I am not sure I want these public.

KAS

I just want to note, that if you open the pic in new window you can zoom in on them

Kas!

Next stop: B Boxes. Flip us.

 

[RadiusNick]

I used a drift punch and a small plastic faced body hammer. To remove the top cap on my P3. Use an old kayfun clone base to hold the contact in place once I got the insulator back on and a mini c-clamp vise grip as a press.


The radius is done different than the p3/classic/Ti line. I've taken the top plate off my radius but just out of curiosity not to fix anything. The pin on the radius is not part of the board but has a wire soldered to it. Should be the same two piece pin though.

it is made out of two pieces(confirmed),
i just wonder how would i press fit the upper part of the 510 pin to the lower part,since it's a spring loaded pin.
i would either have to figure a way to hold the pin in place while press fitting,
or since the spring movement is quit firm it will hold in place by it self.

 

[Bea-FL]

Isn't this the prettiest thing

This morning I just had to use my pink ribbon which, along with the red one, I only use occasionaly, usually on special occasions. No special day today…just felt like it. And somehow the juice seems to be more flavorful!

A great vape!

 

[Ca Ike]

it is made out of two pieces(confirmed),
i just wonder how would i press fit the upper part of the 510 pin to the lower part,since it's a spring loaded pin.
i would either have to figure a way to hold the pin in place while press fitting,
or since the spring movement is quit firm it will hold in place by it self.

I'll take the top plate off one of my radiuses and see what I can come up with. You can press it on with just your finger without the o ring in if you need to get it working fast.


Sent from my iPad using Tapatalk

 

[FringeChief68]

Vaping has less than 1% the cancer risk of tobacco smoke [new study] - Vaping360

 

[classwife]

Direct to Dr. Siegel :
The Rest of the Story: Tobacco News Analysis and Commentary: New Study Provides Strong Empirical Support for New FDA Approach to Tobacco Product Regulation

 

[Hobbs]

 

[AstroTurf]

Pro... Var... Aye!!!

Sent from my iPhone using Tapatalk

 

[AstroTurf]

Like a Big Dog!!!

Sent from my iPhone using Tapatalk

 

[AstroTurf]

Wha What?!?

Sent from my iPhone using Tapatalk

 

[kas122461]

Wha What?!?

Sent from my iPhone using Tapatalk

Surely you are not getting rid of that are you?

KAS