Random DIY mixing and More

FranC

Long time vaper.
Supporting Member
ECF Veteran
Verified Member
  • Oct 1, 2010
    195,516
    645,918
    New Hampshire
    Good morning, random folks:) Woke up to 33 degrees this morning. BBRRRRR. Anyone have plans today? I'm still thinking about doing a 30ml of my Mixed fruit cheesecake. I may just see if I can finalize some recipes for a future mixing session.
     

    FranC

    Long time vaper.
    Supporting Member
    ECF Veteran
    Verified Member
  • Oct 1, 2010
    195,516
    645,918
    New Hampshire
    I actually like the RH minis. Well, more than I like most rda's which is little cause I hate rebuilding.
    I guess I should have paid more attention when I bought them but at least they were super cheap.
     

    FranC

    Long time vaper.
    Supporting Member
    ECF Veteran
    Verified Member
  • Oct 1, 2010
    195,516
    645,918
    New Hampshire
    Darn, Fran. That is cold, I can only imagine what it will be like when you are in winter. We get a few days in low 30's in February and I don't like it.
    Yes, it is and I dread winter. We get a last blast of summer this weekend with temps in the 80's
     

    hittman

    ECF Guru
    Supporting Member
    ECF Veteran
    Verified Member
    Contest Winner!
  • Jul 13, 2009
    61,588
    179,927
    Somewhere between here and there
    Good morning, random folks:) Woke up to 33 degrees this morning. BBRRRRR. Anyone have plans today? I'm still thinking about doing a 30ml of my Mixed fruit cheesecake. I may just see if I can finalize some recipes for a future mixing session.

    It's too early to be that cold. We are still in the 70's for a low and it's been around 90 all week. At least you won't have to haul wood this year.


    I actually like the RH minis. Well, more than I like most RDA's which is little cause I hate rebuilding.

    What set up do you like in them? I think I just need to get used to using them. The dual kanthal coils I put in yesterday let me run closer to the wattage that I'm used to. I only tried one so far but the airflow is super hard to turn. Maybe I should open another one to try.
     

    rosesense

    15years and counting
    Supporting Member
    ECF Veteran
    Verified Member
    Contest Winner!
  • Jan 1, 2010
    17,697
    52,265
    TN
    It's too early to be that cold. We are still in the 70's for a low and it's been around 90 all week. At least you won't have to haul wood this year.




    What set up do you like in them? I think I just need to get used to using them. The dual kanthal coils I put in yesterday let me run closer to the wattage that I'm used to. I only tried one so far but the airflow is super hard to turn. Maybe I should open another one to try.

    Been awhile since I used them but I used 28g and ended up with around 1.2, single coil. I don't remember any issues with the airflow. Did you try aligning it as you put the top cap back on?
     

    NolaMel

    ECF Guru
    ECF Veteran
    Verified Member
    Nov 17, 2012
    12,815
    80,994
    New Orleans
    Good morning, random folks:) Woke up to 33 degrees this morning. BBRRRRR. Anyone have plans today? I'm still thinking about doing a 30ml of my Mixed fruit cheesecake. I may just see if I can finalize some recipes for a future mixing session.
    I’m soooo jealous. It was 80* this morning when I woke up. I can’t mix until I load the last order into ELR. I didn’t realize I’d missed it. Ugh.
     

    FranC

    Long time vaper.
    Supporting Member
    ECF Veteran
    Verified Member
  • Oct 1, 2010
    195,516
    645,918
    New Hampshire
    I’m soooo jealous. It was 80* this morning when I woke up. I can’t mix until I load the last order into ELR. I didn’t realize I’d missed it. Ugh.
    You wouldn't be jealous for long. It's cold. UGH
     

    hittman

    ECF Guru
    Supporting Member
    ECF Veteran
    Verified Member
    Contest Winner!
  • Jul 13, 2009
    61,588
    179,927
    Somewhere between here and there
    Been awhile since I used them but I used 28g and ended up with around 1.2, single coil. I don't remember any issues with the airflow. Did you try aligning it as you put the top cap back on?

    The video I watched showed the inner and outer caps separating. The one I tried doesn't seem to come apart like that. I was thinking to try a single coil in it also. I think I'll open another one when I get home to see if the caps come apart. I have to grab the tip and turn as hard as I can to adjust the airflow.
     

    FranC

    Long time vaper.
    Supporting Member
    ECF Veteran
    Verified Member
  • Oct 1, 2010
    195,516
    645,918
    New Hampshire
    The video I watched showed the inner and outer caps separating. The one I tried doesn't seem to come apart like that. I was thinking to try a single coil in it also. I think I'll open another one when I get home to see if the caps come apart. I have to grab the tip and turn as hard as I can to adjust the airflow.
    Good luck. I don't like fiddley. I have managed to pif mine away.
     

    rosesense

    15years and counting
    Supporting Member
    ECF Veteran
    Verified Member
    Contest Winner!
  • Jan 1, 2010
    17,697
    52,265
    TN
    The video I watched showed the inner and outer caps separating. The one I tried doesn't seem to come apart like that. I was thinking to try a single coil in it also. I think I'll open another one when I get home to see if the caps come apart. I have to grab the tip and turn as hard as I can to adjust the airflow.

    Yes, the top cap should pop off. I have had other attys that were so hard to get off, I had to use pliers the first time.
     

    hittman

    ECF Guru
    Supporting Member
    ECF Veteran
    Verified Member
    Contest Winner!
  • Jul 13, 2009
    61,588
    179,927
    Somewhere between here and there
    Yes, the top cap should pop off. I have had other attys that were so hard to get off, I had to use pliers the first time.

    When I get home tonight, I'll try pulling it with pliers or maybe knock it out from the top with the drip tip off.
     

    Users who are viewing this thread