Lol I did a similar thing with the markten back when I started. But that one you just pop off the back. At least you "modded" your Vuse (ha) instead of buying a pack of smokes
Show the builds you are using right now/ my running thread on my builds
- Thread starter jdake3265
- Start date
- th_trl_thread_readers 0
-
- Tags
- coil builds
- Status
Lol I did a similar thing with the markten back when I started. But that one you just pop off the back. At least you "modded" your Vuse (ha) instead of buying a pack of smokes
I only smoke a cigarette when I want to get a strong nic buzz, it isn't something that I go back to if i don't have any vapes, it is more like when you want to have a treat like a bacon wrapped jalapeno pepper stuffed with cream cheese, is it good for you, no, but it does the job of filling your craving for a stronger nic buzz.
Though I haven't smoked in about a month, I've been vaping a lot longer than that. I don't really like smoking but I also am not against the occasional cigarette like some people are. I'm against switching back, though! I read somewhere that you could smoke one cigarette a week and your body would recover from it fast enough that the negative health effects are basically nonexistent with such infrequent use. Is it true? Idk, maybe. Sounds right to me.
The coil setup I'm currently using in my TOBH:
I angled them as such so that they are directly in front of the airholes since the AFC system on the TOBH is a little oddly placed. Came out to 0.5 Ohms, 4.0 V on 30 watts. Can't decide if I want to put some wick down on the floor of the juice well to help absorb into the wicking or if it absorbs juice from there without any cotton.
I angled them as such so that they are directly in front of the airholes since the AFC system on the TOBH is a little oddly placed. Came out to 0.5 Ohms, 4.0 V on 30 watts. Can't decide if I want to put some wick down on the floor of the juice well to help absorb into the wicking or if it absorbs juice from there without any cotton.
Dual 22ga micros reading .18 on a tobh
Sorry they look crusty i was rewicking and cleaning when i snapped the pic.
Last edited:
Looking good, Im just not a fan of verticalsI ran the TOBH a couple ways.
Vertical
Coils facing the air slot
I wasn't either. Just trying something different with the space I had. Right now is dual 22ga flat wire. Man o man it chucks.
I bet she does. My 22 dual micros are smokestacks as well, I prefer the 24ga ss 316 though, So I will probably go back to building with that when I get the time to rebuild
Nice. Yea I'm back to 24ga now. Just got done with some DIY 90VG/10PG Vanilla Butternut @ 3mg. Yum. Steeping right now.
hey could you give me some tips on ss mesh? im going to rebuild my kraken with it and i have never done it before, i did some research so far, but it still seems like a lot of work.
Im not using mesh, SS316l wire, formerly known as Gplat to vapers.
Here's what I'm using as I opened this post, Been putting a lot of juice through this thing because it's just awesome, it's my "Super Single" Twisted 24ga parallel, 1.5mm coil ID, 4 wraps.
You could say I like it hot. Wick is 100% unmodified hemp fiber.
could you show an action shot of this one? like fire up that sucker.
that is just such a pretty build. all my RDA's are dual coil only 
I never cared until just now, when I wanted to replicate that build.
I never cared until just now, when I wanted to replicate that build.
Quad coil on the big block. 6 wraps, 28g kanthal w/ cotton bacon, vaping at .26 ohms w/ a fresh VCT4.
Last edited:
- Status
