Do you need a new switch? I know they sell them on vaporholics website, i do think thats epics new "main" seller though.
- Status
No, my switch is amazing. And, brand new after all. But I think the new ones are magnetic, so I wouldn't mind trying it out. ::shrugs:: Not a big deal either way.
Would you guys think my Tobeco Plume Veil is safe to use w/ this mech? The 510 pin extends past the threading, but not as much as I'd like, and not as much as the screenies for the Infinite clone does. I can't back this 510 pin out or else it disconnects from the post. I used it a bit on a 0.24 ohm setup, no problems so far but I stopped out of concern. Thanks.
Man, that's right on the edge of safety. That's not stuck out a whole lot than my Atlantis, and as a cautionary tale, I also was able to use my Atlantis for a bit without issue on my Praxis (also a hybrid), but then one day I put it on and proceeded to vent a battery (it was only later that I learned from this forum that the Atlantis should never be used on a hybrid). You may be able to get it to work for a while, but if, somewhere down the road, the insulator in there gets compressed or deformed at all, one day you could easily end up hot-handing yourself. If you do go ahead, I'd say use it with caution.
You can try the o-ring trick with a longer pin. Even if it sticks out a hair now, that pin will push in even more during use as the insulator compresses. 
Elaborate? 
I don't see where I can get a longer pin w/o having to buy another version of the atomizer
This really sucks, I don't have a single atty I can use with this mod. Even the adjustable pins don't adjust out enough to safely vape on this it seems.
I don't see where I can get a longer pin w/o having to buy another version of the atomizer
This really sucks, I don't have a single atty I can use with this mod. Even the adjustable pins don't adjust out enough to safely vape on this it seems.
Last edited:
OK, you may be OK with the pin that you have. Hopefully you will be, cuz I don't know of any other atty or metric fastener to replace that type of pin. 
The reason your pin seems too short may be because your center block isn't seated down far enough. Found this: http://www.e-cigarette-forum.com/forum/new-members-forum/613608-plume-veil-center-post-issue.html#post14363316. There should be some leeway in that connection.
Put an o-ring on the pin is so that it'll protrude and give you some torque when you tighten it to the center block. Use a tiny one, like 4mm OD. You only need a couple of turns. Don't overtighten, or you'll strip out the threads (they're a little more fragile when you're that close to the end) - just tight enough to keep the center block from spinning.
The reason your pin seems too short may be because your center block isn't seated down far enough. Found this: http://www.e-cigarette-forum.com/forum/new-members-forum/613608-plume-veil-center-post-issue.html#post14363316. There should be some leeway in that connection. Put an o-ring on the pin is so that it'll protrude and give you some torque when you tighten it to the center block. Use a tiny one, like 4mm OD. You only need a couple of turns. Don't overtighten, or you'll strip out the threads (they're a little more fragile when you're that close to the end) - just tight enough to keep the center block from spinning.
Thanks! I saw that post you linked, and pushed down my center post because it wasn't seated correctly, just as in that picture. Still didn't make my pin extend any more. And actually, the photos I took and posted make the pin look like it is extending more than it actually is. It extends past the threading, but only about a fingernail's width.
That's where the o-ring comes in (you may need more than one). It limits the amount it will go in when you tighten it, kinda like a shim. You put it/them right at the head of the pin, where the lip is. Pushing down on the block should buy you more threads, so that it'll connect, even with the protrusion.
Last edited:
I got a teeny tiny plastic washer from the hardware store (True Value) and sanded it down to fit under the + pin inside the 510 of my Atlantis just to make sure it would not work its way in to far. I'm using a 4nine, but it would be the same with any 510 hybrid. If the + pin on the atty has any potential to press in, it will with these type of devices. .
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
I got a SS SMPL from Vaporholics, which is EDS's new vendor. And its exactly the same as the one from Vapor Lair which EDS is now saying it's a clone. So no worries if you got it from Vapor Lair. They will warranty the mod even though EDS won't. They are also going to be selling the new SMPL 2.0 switch separate, but they don't have a price yet.
Im selling/trading my authentic copper smpl in the classifieds if anyones interested.
Ha! Lol Yes im sure, i bought this a LONG time ago before this whole fiasco went down or whatever you wanna call it. Im not like that i wouldn't sell or trade it if i wasnt sure. But thanks for the laugh lol.Aer you sure it's an authentic?
j/k you bud.
Finally bought an authentic SMPL. Ordered the copper version from VaporDNA this morning. I was a little put off by the recent sniping between EDS and TVL... almost to the point that I wasn't going to buy a SMPL. But, I've wanted an authentic in copper ever since receiving my copper clone several months ago. As soon as the authentic arrives, the clone will be passed forward to a buddy.
I also purchased an authentic Mephisto V2 with copper AFC this morning. I'm thinking the SMPL and Mephisto AFC may get a matching patina treatment.
I also purchased an authentic Mephisto V2 with copper AFC this morning. I'm thinking the SMPL and Mephisto AFC may get a matching patina treatment.
Well, I finally got around to sanding the points on a cheap pair of jewlers' pliers and fumbled around until I got the switch taken apart and cleaned on my hand me down brass authentic. Lightly sanded the contact point on the switch while I was at it. Then went to the store and got an authentic Mutation X to top it off with (Figured I have an authentic mod now, may as well get an authentic atty too).
Hits like a champ! Loving it, but must say I *hate* the black on brass look. On the hunt now for some non-standard 510 drip tips that will fit this atomzier.
Hits like a champ! Loving it, but must say I *hate* the black on brass look. On the hunt now for some non-standard 510 drip tips that will fit this atomzier.
I got mine today as an early Bday gift from my son. (who happens to share my Bday)
I think he was just tired of seeing me mess with cig a likes and still smoking analogs. I have the dark horse RDA.
Love it! I am going to make a post in the general section about the entire B&M experience. This is my first time going to one and they deserve a shout out for just being great!
I think he was just tired of seeing me mess with cig a likes and still smoking analogs. I have the dark horse RDA.
Love it! I am going to make a post in the general section about the entire B&M experience. This is my first time going to one and they deserve a shout out for just being great!
Ok so the SMPL 2.0 is out.... who's in? https://thevaporlair.com/shop/devices/smpl2-0-stainless-rem-creations/
- Status
Similar threads
