My first build on the SQuape reloaded, .78 build,leaking around the bottom actually coming out of the adjustable air holes any ideas? Yes it's a clone!
Last edited:
Squape Reloaded Clone
- Thread starter yungstu
- Start date
- th_trl_thread_readers 0
- Status
I done two things,pushed the coil down closer to the vent hole,and think that I had the base screwed on too tight kind of strange but its not leaking at least right now..
Did your post wiggle on your ivogo deck?!sketchy!!
Yep. Its a mess.
Oh, the Kingtu is making a very loud, annoying, high pitched whistle so some debris in the air passage. My 2 African Greys love it. Me, not so much, so I need to clean that out.
Kingtu sent me a free sample of their 4 Century mod. I thought it was going to be a clone of the expensive SvoeMesto Semovar but it turned out to be a novelty mod with a touch switch near the top cap. It unfortunately lacks an adjustable center pin and leaves a gap with almost all toppers.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
The E-holly 35w has the same problem the fix is pull the pin and replace with a shorter grub screw (2.0x6) Maybe it would work on that too
Last edited:
About the same. It does make a cool space shuttle sound though
Ok, the airhole openings for the Kingtu are smaller than the Ivogo's afc ring. I might try to switch them out.
My Kingtu clone was starting to whistle too. After playing around with the AFC ring, I found a way to stop the shrill whistling sound. If I turn the ring slightly past the point where it clicks into place, the whistling is gone! I think the whistle comes from a slight space under the ring and if I turn the ring slightly past the chosen hole, the ball bearing will lift the ring and close the space under the hole. Hard to explain, but it seems to work.
Hi friends, came across a great video and a way to stop the squape R from leaking!! For those who are interested this video showed wicking the squape as usual then cutting each side of the wick in two. Then leaving the bottom half long and putting it into the juice channels then cutting the top wick short. This stops the leak. Hope this helps.
My top piece is not leaking as I unscrewed the chimney, pulled off the tip, and pulled on it while holding my finger over the top hole and it's tight. It's still tight after screwing the chimney back in. It leaks through the air hole when I assemble it. It's no longer completely air tight but close when the bottom piece is screwed on. It might be a build issue but I've tried stuffing the juice channels with wick. I'm not sure what to try next.
Sent from my GT-N7100 using Tapatalk
Sent from my GT-N7100 using Tapatalk
Tomorrow when I have better lighting I will take a picture of how to wick it for everyone. It leaks when the wick is too thin or too short.
I use a 7/64" drill bit for coiling the W deck.
Actually, Chuckie might still be coiled. Give me a little bit and I will wick it.
I use a 7/64" drill bit for coiling the W deck.
Actually, Chuckie might still be coiled. Give me a little bit and I will wick it.
I put the same flavor I had in my squape r clone in my lemo, and it made me realize the flavor was quite muted in the squape, since then the squape has been cleaned not used.
That might've been the wicking, Nailz...too much, maybe? Or coil height. Or too much air.
Dunno. Mine is great. But I just started playing with the Heron, so SqR's on break until I can get some magnets for my other mod. Then I'll have both of them set up, cuz they really do hit and taste about the same. Awesome. Orchid's no slouch either. That's the other one I have to get a working mod for.
Wicking, wide deck. Pics are goofy. This is my second attemp posting.
Attachments
Last edited:
- Status
Similar threads
