Squape Reloaded Clone
- Thread starter yungstu
- Start date
- th_trl_thread_readers 0
- Status
AMD I appreciate what you did with the pic,if I'm not mistaken I watched Rip on the kayfun,I also done something a little bit different than the normal way that I do when it's wicking time ,i ran the oc through the coil,like rabbit ears I pulled the WIC straight up then I took a chimney or sleeve and I cut the wick flush with the top of the sleeve ,being very cautious I pushed the wicks down then I added just enough liquid to the wake to replace it where I usually do it but I couldn't really see because of the sleeve,long story short hope I'm not confusing anybody but it's working when I first saw the video I'm thinking to myself this is got to be too easy it's got to be a downside to it but anyways I tried it this evening so far all is good.
You should contact them again. Tell them you need the parts and you don't have anything to order ATM. I think with that part in particular, there IS an option of sending it separately, without having to place another order. They offered it to me, but I just happened to be placing another order at the time. And about to order again, because there's a 10% coupon out right now.
Yes they're sending it separately .You should contact them again. Tell them you need the parts and you don't have anything to order ATM. I think with that part in particular, there IS an option of sending it separately, without having to place another order. They offered it to me, but I just happened to be placing another order at the time. And about to order again, because there's a 10% coupon out right now.
Then you want the one made by StattQualm- Works out of the box.
Completely true - price and availability is a downside though.
oh well - they are available again since beginning of November.
€135 with no extra decks - these kind of prices attract the attention of the clone manufacturers.
I would say the reason these aren't sold out is because of the clones.
Looks like this thread is dead or all is still eating turkey Was hoping to hear if midsouth squape r are trouble free and where to order from reckon poolprousa is a turkey eater not a die hard vaper (or is it vaperer)
Was hoping to hear if midsouth squape r are trouble free and where to order from reckon poolprousa is a turkey eater not a die hard vaper (or is it vaperer)
Last edited:
Looks like this thread is dead or all is still eating turkey
I have the Ehpro SQr from Midsouthtrading. Worked right out of the box and no leaking. I have been using it everyday over the last few weeks, no problem. Great vape! I was told not to post links to vendors that are not part of ecf. I will pm you a link.
A page or two back Mr Midsouthtrading himself posted.. His emails listed too.
Thanks jbarrick I didnt see his email addy I will have another look thanks Monotremata
I didnt see his email addy I will have another look thanks Monotremata 
I have a Squape Reloded Clone, it is work, but i have a problem with chimney.
When i made the first setup is leaking a lot. I read many solution here, on this topic, and one of them is to put an small oring on top of the chimney, but the working solution was change the tank oring. I think that this oring on the top of the chimney made preasure on the deck, and now inside the chimney on a small portion, in 2 oposite parts, it is is scratched a little bit, the anodized is off, and i can see the aluminium.
My problem is healty one: it is safe? The scratched portion wher is pur aluminiun i think is touching the lichid and maybe the cotton, some chimichal reaction are posible.
I d'ont know to keep use it or not.
So, any opinion are wellcome.
When i made the first setup is leaking a lot. I read many solution here, on this topic, and one of them is to put an small oring on top of the chimney, but the working solution was change the tank oring. I think that this oring on the top of the chimney made preasure on the deck, and now inside the chimney on a small portion, in 2 oposite parts, it is is scratched a little bit, the anodized is off, and i can see the aluminium.
My problem is healty one: it is safe? The scratched portion wher is pur aluminiun i think is touching the lichid and maybe the cotton, some chimichal reaction are posible.
I d'ont know to keep use it or not.
So, any opinion are wellcome.
I got one from FT....I am afraid to leave it on any of my mods at night.Leak city,shorting,i did not start vaping yesterday,purchased many clones.This one takes the cake.
My Kingtu's positive pin started the resistance jumping yesterday. My 1.2ohm build was reading 6.5ohms, lol! That's higher than Chucky ever got to! Its been a rock steady base, 100% better than Chucky ever was so it surprised me. I couldn't get it to settle down, so took that insulator I made for Chucky and put it in. Its been fine since, but its a little loose on this atty. The pin and head of the pin are smaller. When I have time, I will make it a new one.
I'm a week into the Ehpro (no logo) from Midsouthtrading. Comparing it to the Kingtu, the ohms and center pin have been solid, it's a little airier which is fine with the adjustment ring, it's easier to fill because it doesn't get the "vacuum" effect along the sides. The windows are a little sharply cut and I'm not sure what the coating is on the decks. It did come with all three. It's working quite well. I like this one much better and have put the Kingtu to one side (parts are not interchangeable, btw). This and the 22mm Erl clone are in the rotation for now.
The parts aren't interchangeable? I thought midsouth was giving decks from the Kingtu with the EHPro clone? I could be wrong though.
I do need to see if parts from my Kingtu interchange with the authentic. They look like they will. The Ivogo is definitely different.
- Status
Similar threads
