Stallion hoofbeats at my door

[rver]

I had ordered 1 bx of stallions and it arrived yesterday. After looking them over I put 2m/l of juice in two of them (different flavor's) and started vaping. The first thing I did was shake the hell out of them every which way...no leaks at all. I then put them both on each of my twist and left the setting at 4.6 that I use for my std. carts. Both of them performed well but I felt that at that setting, it was just a bit to warm for me. after trying different voltages, I then reset the voltage to 4.0...and that turned out to be my sweet spot. Lots of vapor, good TH and no loss of flavor. If they hold up better then the std. carts, I think that gotvapes has a real winner. I then tried them in my provari with very good results. I checked the OHMS reading and one showed 2.9 and the other came in at 3.0...perfect for the provari untill I got carried away cranked it up to 5.6. Good grief, I was sure I was going to pass out...tons of vapor, good TH but a total loss of flavor. I quickly went back to my sweet spot and had a vaping ball.


The next test was important to me as I'm a cart tank person. Iwanted to try one in one of my 5ML tanks so with my thumbnail, a sharp knife, good old acetone for final cleaning and of course a few choice cuss words, I had a nice clean stainless stallion. I punched the holes the exact way as was done with my other carts, I did it with my saddle valve...when the needle pops thru, another half turn. The end result was just as good as the original method.


The last test is to see how they hold up...only time will answere that...

 

[vikeme28]

Awesome news. Been hearing great things and if they work in a tank even better but not a deal breaker. The better half leaves for Boston for two weeks tomorrow so i will be ordering a box or three. Better to ask for forgiveness

 

[dannoman]

Good thorough run through...much appreciated...

I had ordered 1 bx of stallions and it arrived yesterday. After looking them over I put 2m/l of juice in two of them (different flavor's) and started vaping. The first thing I did was shake the hell out of them every which way...no leaks at all. I then put them both on each of my twist and left the setting at 4.6 that I use for my std. carts. Both of them performed well but I felt that at that setting, it was just a bit to warm for me. after trying different voltages, I then reset the voltage to 4.0...and that turned out to be my sweet spot. Lots of vapor, good TH and no loss of flavor. If they hold up better then the std. carts, I think that gotvapes has a real winner. I then tried them in my provari with very good results. I checked the OHMS reading and one showed 2.9 and the other came in at 3.0...perfect for the provari untill I got carried away cranked it up to 5.6. Good grief, I was sure I was going to pass out...tons of vapor, good TH but a total loss of flavor. I quickly went back to my sweet spot and had a vaping ball.


The next test was important to me as I'm a cart tank person. Iwanted to try one in one of my 5ML tanks so with my thumbnail, a sharp knife, good old acetone for final cleaning and of course a few choice cuss words, I had a nice clean stainless stallion. I punched the holes the exact way as was done with my other carts, I did it with my saddle valve...when the needle pops thru, another half turn. The end result was just as good as the original method.


The last test is to see how they hold up...only time will answere that...

 

[badkolo]

Great news, The stallions truly are trampling in the scene.

 

[REET_AZ]

I saw Bad post a comment earlier that you needed to add a drip tip on the first fill - and that after the first fill - no. Does that mean as long as you have used a drip tip from the beginning that you can on the refill?

Sorry to ask what must seem a silly question, but i really hate using the flat end carto cap. Just clarifying so I do not have any surprises.

Thank you for any response in advance

 

[vikeme28]

Correct me if I'm wrong people but I believe you need to wait till its been used or empty to put a regular drip tip in because it will push the juice out if its full of juice. If you put the drip tip in when its empty it will push the filler down and then when you fill from then on you will be OK because that's all the higher your juice will be.
Basically push the filler down to match your drip tip length and your good to use it from there on with no issues
I'm sure that was as clear as mud

 

[REET_AZ]

Thank you! I get it. That is great!

 

[rver]

Sounds logical VIKE...will give it a try when I empty the cart....now all I have to do is get on my knees and put my hands in that praying position and beg BAD to stock plain stainless Stallions for us tank dwealers...

 

[dannoman]

Lets see how y'all like them in a tank (someone is goign to need to get back with us!) before we go there...so far the early feedback has been great gnereally speaking...

Sounds logical VIKE...will give it a try when I empty the cart....now all I have to do is get on my knees and put my hands in that praying position and beg BAD to stock plain stainless Stallions for us tank dwealers...

 

[WallyO]

I had ordered 1 bx of stallions and it arrived yesterday. After looking them over I put 2m/l of juice in two of them (different flavor's) and started vaping. ...

Were you actually able to get two mm in? I just filled two of mine. One would only take 1.8 and the other only 1.6. I know the box says 2.2 but that's probably just an empty tube with no innards.

 

[rver]

Same here WALLY...I have to wonder if the fact that I pushed the filler down a bit to get the driptip on has anything to do with it?

 

[rver]

edit...I really don't care because I have one in the tank now for the past couple of days and will put the rest of them in shortly. the one in the tank is working great for now.

 

[BonnyC]

Were you actually able to get two mm in? I just filled two of mine. One would only take 1.8 and the other only 1.6. I know the box says 2.2 but that's probably just an empty tube with no innards.

Actually, I was able to get quite a bit of juice in them. Thing is, I had to use another needle that was about 1.5 inches long. When I use my shorter needles that came with the Phoenixes, it didn't seem to take as much. I'm guessing, and it makes sense, that the filler is soaking more juice and it's not filling at the bottom so it appears to be full sooner. I was always told that the old filler cartos would hold more if you filled it from the bottom with a syringe stuck far down the side. Could just be a fluke, I dunno. What I do know is that when I filled the syringe as much as I did with the others, I had to go back and get more juice in it because that stallion wasn't full.

 

[silversx]

it would be cool if the blanks came in stainless as most carto users now are big on tanks ..

and especially with bogegate going on.. good time for people to switch cartos

 

[dodari]

Didn't quite understand when Bad filled one of these. Is there a tiny hole you load it through, or do ya shove the needle down the side past the plug? Is it a plug or what?

Sorry, guess I'm in 'I don't get it mode'.

The reports coming in sound good, just hope it's easier to load than the Phoenix BCs. Those little holes for the syringe needle are very hard for me to see.

 

[vikeme28]

Very easy. Shove it into the polyfil and fill

 

[rver]

I agree, go down the side of the wall, and I use an 18GA 1and1/2 inch needle...there is simply no filling hole.

 

[r77r7r]

These don't come with condoms for filling/protection?

 

[silversx]

a true stallion does not need protection

 

[YoMa!]

They do come with condoms with a stem inside. I believe it is only the "true stallions" that do need protection.