It's just as good in a blizzard...and...it don't melt.
there is NEVER any justifiecation needed for ICE CREAM.
![]()
there is NEVER any justifiecation needed for ICE CREAM.
![]()
I was thinking of foregoing the veg soup I made for the piece of homemade pound cake my granny sent home with me today. I'll probably just have both.![]()
One more thing about "leaking tanks". I don't know if you guys had been referring to Clearomisers as tanks or not, but I've heard some of the Clearo's i.e. Stardust start to leak where the plastic tank mates with the metal battery connection piece.
Another thing I've noticed with actual tanks is o-rings. The J-Tanks had CRAZY tight o-rings and I had to fight to get the caps on/off, AND to get the cartos in/out as well. Jam, jam, jamming things just ends up nicking, tearing, damaging the o-rings and then you get leaks.
I got the Phiniac carto/tank tool with my Phiniac tanks, and I cannot recommend it enough. It really just sliiiiiiiides the cartos in/out and doesn't damage the o-rings, and I have gone through a LOT of cartos.
I don't remember where they came from, which is good because I won't be getting any more! 
If the water in the pipe doesn't work for you, think about it like this. If you are traveling downhill in your car with NO brakes, you will go quite fast, IF you start to apply the breaks somewhat that RESISTS your speed and you start to slow down some. If you apply the breaks harder they RESIST your speed even more and you slow down further. Resistors, resistance, atomizers, cartomizers all RESIST current flow. The less they resist (lower resistance) the more current flows.
Lower resistance attys and cartos will ALLOW more current to flow, more vapor, warmer vape. Higher resistance attys and cartos RESIST more current flow, so less vapor and a cooler vape. If you go to the extremes, your Provari will error out to protect you. If the resistance gets TOO low, meaning there is little to no resistance, current could flow way too high, so it errors out.
I know attys, and learned over 1.5 years of dripping. I'm talking regular LR attys and dripping, not the heads in Vivi's or the like. Mine all came shipped with primer (who knows what it is, maybe pure VG or PG to protect the coil), I always blew it out. Then (remember I used only LR attys which burn hotter and neeed to be wet), I would add about 4-5 drips, and puff puff puff the first few mouthfuls without inhaling (primer), then I would drip about 4-5 drips and vape for a bit, once it started getting slightly harsher, I'd add another 4-5 drips, and repeat.
Depending on the juice sometimes I could go 2 weeks on a single atty. After they started getting fouled up with juice gunk, and the taste was starting to turn bad, I would toss in a ziplock. After I had a couple, I would boil them on the stove for about 5 minutes, dump all the water, refill the pot, reboil, and repeat until the water looked and smelled clear. Then I would blow out the water, and let dry for about 24 hours, then start back up with the 4-5 drips and vape.
Not all of my attys came back to life, some only tasted burned after cleaning and they were tossed, some came back like new, and others were still OK, but not new new.
Xtar charger I ordered came in. I forgot to order extra spacers. I can now charge one 18350 at a time. I have 6 dead.:
If the water in the pipe doesn't work for you, think about it like this. If you are traveling downhill in your car with NO brakes, you will go quite fast, IF you start to apply the breaks somewhat that RESISTS your speed and you start to slow down some. If you apply the breaks harder they RESIST your speed even more and you slow down further. Resistors, resistance, atomizers, cartomizers all RESIST current flow. The less they resist (lower resistance) the more current flows.
Lower resistance attys and cartos will ALLOW more current to flow, more vapor, warmer vape. Higher resistance attys and cartos RESIST more current flow, so less vapor and a cooler vape. If you go to the extremes, your Provari will error out to protect you. If the resistance gets TOO low, meaning there is little to no resistance, current could flow way too high, so it errors out.
i love phiniac! Chris over there is a good dude! I was gonna order one this week..but now will have to wait..hv to save money for trips to hospital everyday. Thanks everybody for the kind words..really means alot. I just moved where i am living now a month ago..and you guys for the past couple days hv been my social life..lol. And a great group of ppl here.![]()
Is that me pretending to be you??We must have been siblings separated at birth...
SP speechless.Can't have that.
![]()
You can also clean them with alcohol like Vodka and let it sit in the atty or some vendors sell an atty refresher that is alcohol-based. I have good luck with that.![]()
My Newest fun tank the Vivi Nova.just 1 but I have 106 on their way.No leaks..
i love phiniac! chris over there is a good dude! i was gonna order one this week..but now will have to wait..hv to save money for trips to hospital everyday. thanks everybody for the kind words..really means alot. i just moved where i am living now a month ago..and you guys for the past couple days hv been my social life..lol. and a great group of ppl here.![]()
Put some bananananananana in with cake and you will think you were just in Downtown Bakery located in Steubenville Ohio. Birthplace of Dean Martin..and the best bakery ever...
Or...You could drink the vodka with some cheese and crackers get a new atty out of the package and throw the old atty away...