How to test coil resistance then? Measure by touching probe ends to each post?
The "REOMIZER" Rob's Rebuildable Atomizer
- Thread starter rasci2
- Start date
- th_trl_thread_readers 0
- Status
How to test coil resistance then? Measure by touching probe ends to each post?
I'm getting problem with shorting out... i guess time to replace coil//wick. I don't see any danger of coil touching the base but i did lay some extra wick on top of the original wick just to hold a little more juice and i did bend the thing down towards the middle hole...
It will. It is no longer a theory, through extensive testing I've determined it to be fact. (I never make mistakes, I just test a great deal.)
Jack
Jack
Where can I get new screws? I received 2 and in both one screw was striped. I put them in my sonic cleaner and used a different screw driver, I got them out, but I'm sure they won't last long.
I'm having this same problem, one of the screws is almost stripped out.
I am sure I can find them at the hardware store. Does anyone know the size? I'd like to find some allen screws to replace them with.
These should work I just ordered some. I will let you no as soon as they arrive
Part # 92029A085
McMaster-Carr
Part # 92029A085
McMaster-Carr
Thank you Rob. My Woodvil came today and the Reomizer is working great. I miss the blind squonk though. It truly is a blink squonk now because I can't see or tell how much juice is getting to the wick. I'm sure I'll figure it out though with practice. This RA is so cute and small and so quiet. I love it but I haven't rebuilt it yet so that might change. 
I stuck a piece of cotton wick under the coil and around the juice hole so it's holding more juice and less squonking. YaY!
I would get another one for my other Woodvil but I have about 100 shorty cartos I need to use up first.
Edit: Oh, I almost forgot. Kisses coming your way.
I stuck a piece of cotton wick under the coil and around the juice hole so it's holding more juice and less squonking. YaY!I would get another one for my other Woodvil but I have about 100 shorty cartos I need to use up first.
Edit: Oh, I almost forgot. Kisses coming your way.
Mine keep shorting out and they are not touching bottom... something else... maybe I have not observed ALL the rules.
Like wraps too close maybe... or the top cap touching something, or just defective coil making.
If I fiddle with the coil it will work for a while, then short out again. Its great when its working but I haven't figured what I'm doing wrong.
I like the idea of using some extra cotton or wick to hold more juice as it comes up from the bottom hole. How can the juice get to the wick if it's above the base?
Like wraps too close maybe... or the top cap touching something, or just defective coil making.
If I fiddle with the coil it will work for a while, then short out again. Its great when its working but I haven't figured what I'm doing wrong.
I like the idea of using some extra cotton or wick to hold more juice as it comes up from the bottom hole. How can the juice get to the wick if it's above the base?
yup o ring is in there
this isn't new to me... i have a few rba's and once in a while get lucky
this isn't new to me... i have a few rba's and once in a while get lucky
Sorry I'm no help. That was the only thing that came to mind. I hope you find the problem and share it with us.
There is a gasket in the atomizer and a gasket around the negative post . If ether one is broke the atomizer will short . You can remove the center post and pull out the gasket check for any rips or cracks. I have tons of the gaskets let me no what you find . Of course your welcome to send the atty to me
I will post some picks later of the atomizer taken apart . If not tonight I will do it first thing ion the morning
From McMaster:
Type 316 Stainless Steel M2
Pitch: 0.4 mm
Part#: 92029A085
Metric Type 316 SS Cup Point Set Screw M2 Size, 3mm Long, .4mm Pitch
Seems that the top cap sits very loose, is anyone else having this issue? In fact, it will pop off if I tip it upside down. I pinched the outer chamber a bit, which helped, but still far from perfect. I'm thinking a little plumbers tape will fix this...
I have an idea- everyone should magnetized their screw drivers and allen wrenches!! This way, the little screws will stay on the tightening devices and you won't lose them so easily. Remember how to do this? All you do is rub them on a strong magnet, about 100 strokes!!
Haven't had the issue. Perhaps a PM to Rob is in order. Remember he only modified these and didn't design or make them so QC won't be up to his specs.
Hugs, Feisty Alice
- Status
Similar threads
