The Reonauts new lounge
- Thread starter Sterno
- Start date
- th_trl_thread_readers 0
- Status
I'm pretty much a confirmed dual coiler myself. I have been for a couple years. But, I have been running a single 2.5mm 24g coil in my Stumpys lately; and I must say, it's quite good.
hmmmm I know Rob said on those that he couldn't adjust it for all atties, but dunno if there are differences in RM2's or not. You could always have him put in the adjustable 510 if it bothers ya, and send the rm2 with it and he could probably make it fit flush. Or email and ask if he can
jup I've heard a lotta folks say the stumpy's are great with one coil...but those are definitely not in my budget
Finally built my S.O.D 5k from Science of vaping: “S.O.D. 5K” – ATOMIZER KIT
I installed 26gK1, dual verticle 8/7, 2.5mmID coils.
The SS cap that comes with the atty had only 1 pinhole airhole in it. I emailed them as it has to be a defect.
I also ordered the anodized chuff cap. The build was a complete PITA for dual verticles. I am sure it will be worse for horizontals.
Initial impressions are huge airy vape, flavor is a 7 out of 10. I am hoping it improves as the wicks break in. For $30 bucks hard to go wrong but.....
I installed 26gK1, dual verticle 8/7, 2.5mmID coils.
The SS cap that comes with the atty had only 1 pinhole airhole in it. I emailed them as it has to be a defect.
I also ordered the anodized chuff cap. The build was a complete PITA for dual verticles. I am sure it will be worse for horizontals.
Initial impressions are huge airy vape, flavor is a 7 out of 10. I am hoping it improves as the wicks break in. For $30 bucks hard to go wrong but.....
Finally built my S.O.D 5k from Science of Vaping: “S.O.D. 5K” – ATOMIZER KIT
I installed 26gK1, dual verticle 8/7, 2.5mmID coils.
The SS cap that comes with the atty had only 1 pinhole airhole in it. I emailed them as it has to be a defect.
I also ordered the anodized chuff cap. The build was a complete PITA for dual verticles. I am sure it will be worse for horizontals.
Initial impressions are huge airy vape, flavor is a 7 out of 10. I am hoping it improves as the wicks break in. For $30 bucks hard to go wrong but.....
Looks good. I'd have to try that vertical build with ss mesh wicks.
I don't understand. Is it just brass showing (the brass that would normally be down in the well), or is it an air gap below the atty?
oh I thought it was a gap between the atty bottom and the mod......did you have mini lp'd? If so you may have an sp rm2, that will show an area of brass that has been milled down
Seven inches of heavy snow last night...yucky.
Stopped at the local vape shop today and bought a Trinity glass drip tip. Nice wide bore but only looks good on my Atomic rm4's.
Have you got an RM4 Deb? I get great flavor, .7 ohm single coilwith both airholes open wide. More flavor than my dual Derringer actually.
Stopped at the local vape shop today and bought a Trinity glass drip tip. Nice wide bore but only looks good on my Atomic rm4's.
Have you got an RM4 Deb? I get great flavor, .7 ohm single coilwith both airholes open wide. More flavor than my dual Derringer actually.
One of HRH's friends is in New York and couldn't get to work today because of the snow. I about fell out of my chair; it was 85f here today.
T
T
I second the RM4. Old school atty, for sure; but tough to beat for a flavor atty. I have a couple of them on my Grands, I build mine with dual 26g, about .4 ohms.
18490 ? or 14500 ?My mini is a plain old mini from waaaaaaaay back
thank you Classy
and ya an old 14500 would most definitely not be LP unless someone made it that way for you 
- Status
Similar threads
