After washing my Vmod in warm soapy water I noticed that juice has caked on the inside of the bottom chamber. So far I have tried soaking it in lemon juice, isopropyl alcohol, and it currently is soaking in listerine, but I can't seem to get it clean. Is this normal? Is there a way I can take the Vmod apart so that I can scrub the inside chamber?
The Vmod XL 18650 Bottom Feeding Mod from Vapage.com
- Thread starter AlmightyGod
- Start date
- th_trl_thread_readers 0
- Status
Try a plain PG soak, and gently go over it with a toothpick. Also, vodka helps as well.
Thanks for replying. I'll try the PG soak next.
Hot water & Everclear haven't failed me yet.
What the heck are you vaping?
Either Bounty Hunter or Highbrow's Tabac De Cirac.
Mainly I was just being lazy and hadn't washed the Vmod in awhile is what probably caused the problem. I had no idea that juice could get stuck like that to metal and if something like that were to happen I thought it would happen to the top chamber where the juice would be heated up by the atomizer.
Can anyone recommend a good place to get the AW IMR 18650 batteries that I always hear so much about on this thread? I have been using trustfires, ultrafires, and the Vapage brand batts. Is it worth it to get AW IMR's?
my favorite for AW IMR's; $1.89 shipping up to 3 batts; SuperTmanufacturing.com
Way to go Dana. You've got good taste! Very good picks, imho, of course.
The v2 is simply adorable -- you won't believe how tiny it is......and just as fine as the XL overall. I'm in love with it all over again with it's new very girly pink flowered hippie shell.
The v2 is simply adorable -- you won't believe how tiny it is......and just as fine as the XL overall. I'm in love with it all over again with it's new very girly pink flowered hippie shell.
U can try ICR SAnyo too, for me are almost the same like IMR.
hi all,
been going through this thread and i had two questions that i couldn't find an answer to:
1) for stacked batteries at "6V" vaping, is the general consensus to use the (I have a ~3.0 306 atty that i'm planning on using with it)
- TENERGY 30200 LIFEPO4 RCR123A 3.0V (3.2V) 750MAH - Tenergy 30200 LiFePO4 RCR123A 3.0V (3.2V) 750mAh Rechargeable Battery
- TENERGY 30201 RCR123A 3.0V 900MAH - Tenergy 30201 RCR123A 3.0V 900mAh Rechargeable Li-Ion Battery .
2) for those using the 306 (cisco spec) atty, what kind of drip tips are you using with it?
Thanks all!
been going through this thread and i had two questions that i couldn't find an answer to:
1) for stacked batteries at "6V" vaping, is the general consensus to use the (I have a ~3.0 306 atty that i'm planning on using with it)
- TENERGY 30200 LIFEPO4 RCR123A 3.0V (3.2V) 750MAH - Tenergy 30200 LiFePO4 RCR123A 3.0V (3.2V) 750mAh Rechargeable Battery
- TENERGY 30201 RCR123A 3.0V 900MAH - Tenergy 30201 RCR123A 3.0V 900mAh Rechargeable Li-Ion Battery .
2) for those using the 306 (cisco spec) atty, what kind of drip tips are you using with it?
Thanks all!
I am going to do the I would not suggest you use 2 batterys to vape at 6 volts however I consider myself to be a responsible adult who looks after my equipment as I suspect you do.
Yes it works with all safety caveats I can add without being flamed.
Use the extended 306 drip tip as the stamdard one is a little short. Works but the longer one brings everything above the cone.
Sent from my MB860 using Tapatalk 2
Yes it works with all safety caveats I can add without being flamed.
Use the extended 306 drip tip as the stamdard one is a little short. Works but the longer one brings everything above the cone.
Sent from my MB860 using Tapatalk 2
Yes have those as well.
Using a 3 ohm dripping atty perform well for 3 - 5 hours them I have to swap for the spare.
Both options work and work well but my preference is to keep with the 18650 and use a 1.5 ohm atty. I don't have to carry extra battery's to get through the day.
In the advent of placing the Kick under the bottle leaving you free to retain the services of a 18650 I think that is an option I will try in the future.
Sent from my MB860 using Tapatalk 2
Using a 3 ohm dripping atty perform well for 3 - 5 hours them I have to swap for the spare.
Both options work and work well but my preference is to keep with the 18650 and use a 1.5 ohm atty. I don't have to carry extra battery's to get through the day.
In the advent of placing the Kick under the bottle leaving you free to retain the services of a 18650 I think that is an option I will try in the future.
Sent from my MB860 using Tapatalk 2
My new shells and baby V Mod are on the way. I am so excited!!! I also have matching drip tips on the way I am having wayyy to much fun with this. Can anyone tell me what it is about the Silo's that make the flavor so good and the vape so smooth? I tried one on my Provari out of desperation and it obviously didn't work. I wish Vapage would make some for use on non bottom feeders as well cause I would buy stock. Oh wait I think I already did when I just ordered 16 two packs LOL
- Status
Similar threads
- Locked
- Locked
