smilee no worry....if that were to happen I would send you one of mine when they come in!!
The Vmod XL 18650 Bottom Feeding Mod from Vapage.com
- Thread starter AlmightyGod
- Start date
- th_trl_thread_readers 0
- Status
OI have a question concerning the draw on the VMOD-XL. Mine has suddenly tightened up
I have removed the atty and once removed seems to draw just fine. Cleaned it up....checked the draw... re-installed and still the draw is tight I visually checked the internal threads and suspected an oring....nope orings are where they are suppose to be.....so what might be going on here? any ideas??
I have removed the atty and once removed seems to draw just fine. Cleaned it up....checked the draw... re-installed and still the draw is tight
I visually checked the internal threads and suspected an oring....nope orings are where they are suppose to be.....so what might be going on here? any ideas??I have a friend in NY, which is the case in Poland, as it fails to ask his imported - xl will be with me for half the year - and I will stand strongExtra thanks, fro you is only 8000 km
OI have a question concerning the draw on the VMOD-XL. Mine has suddenly tightened up
I have removed the atty and once removed seems to draw just fine. Cleaned it up....checked the draw... re-installed and still the draw is tight
Try blowing your atty out in a paper towel, it sounds flooded, especially if it happened suddenly.
OI have a question concerning the draw on the VMOD-XL. Mine has suddenly tightened up
I have removed the atty an once removed seems to draw just fine. Cleaned it up....checked the draw... re-installed and still the draw is tight
can for xl squeeze firmly in your hand is too strong
you tried other atty ?
as has been blowing it does not help throw him into hot water
And if that does not work and it means that your xl is useless - then send them to me
its only 9k km
OI have a question concerning the draw on the VMOD-XL. Mine has suddenly tightened up
I have removed the atty and once removed seems to draw just fine. Cleaned it up....checked the draw... re-installed and still the draw is tight
Also -- it could be you aren't getting air. I know you said cleaned up -- but did you give it a bath in hot water? It could be that the bottom air holes are clogged. Also--you could have re-assembled the chimney & cone too tight.
Other vmodians know this "air" area better than me --- so I'm sure someone else will chime in.
hmmmm... you might be on to something here.....i tossed a new atty on and voila....smooth draw....
so the tight draw is because the weee holes around the cylnder head just above the threads are clogged.....good advice tear, thank you
do i need to buy batteries or do they come with the "complete" XL kit? IF they do come with the kit, i just need to buy a charger correct?
damn, that kinda sucks 85 bucks and its not even complete lol. Oh well still cheaper than most. Can anyone link me to a good source for batts & Charger?
Vapage E-Cigarettes, E-Cigs, Disposable E-Cigs & Electronic Cigarette sell protected 18650 batteries. or you can buy some AW 18650 IMR at Electronic Cigarettes and AW batteries by Super T
sleep with one open! LOL! awesome!! someone is really excited!'
thanks, but even as I sleep with one eye to check the status
The Vmod XL and the Vmod II are only be sold "a la carte" right now, I believe. They come with 1 atty & 1 carto and 2 drip tips.
That means you will have to buy a charger and batteries. The Vapage batteries have good reviews and both sizes are sold by Vapage. Vapage has only had a charger for the 14500's--so far. RTD and Super T are 2 popular battery sellers. I picked up a Pila charger when I got my first mod. IMO it's worth the splurge.
And jojo --- vapin15 is the code for 15% off. Free shipping for orders over $50 too.
- Status
Similar threads
- Locked
- Locked
