The Vmod XL 18650 Bottom Feeding Mod from Vapage.com
- Thread starter AlmightyGod
- Start date
- th_trl_thread_readers 0
- Status
The little white flat o ring that is on the threads at the base of the atty/carto -- it's kind of rubbery. It won't hurt anything if you don't remove it -- as long as you can screw on tight enough to fire. I have had to remove them. YMMV
If the white rubber thingy is the condom -- yes, it needs to come off.
Don't try and remove anything from the bottom of the atty----except the condom!
Dripping with the .357, that gurgles like a hippo in a vat of champagne, but hits like a hippo too, has made me more accepting of wet vapes, just slather that juice in there and taze it, bro! But let me tell ya, new users, flooding the atty like a rice field, then pulling the extra juice back by finessing the return on the squirsh is a very special Vmod skill that belongs on your resume. Take the mouthpiece off, get a flashlight, observe and practice it. Then every hit will be your perfect storm, fresh as a newborn!
Its def a skill to feed the 357 right but it can be done and if you master it it is worth the effort I have a 357 in each of my xls 2 510s and 1 901 with adappter
Sent from my SPH-D700 using Tapatalk
Last edited:
hehe XD have a debridged joye 306 and that it's also gurgeling
I'm finding my .357 runs so hot it's best at 3.3 volts. In fact, the IKV 1.8 ohm 510 atty is about as good, for under half the price, it takes less power and thanks to the bridge it doesn't spit so darned much. The .357 has one plus for dripping, which is the "reservoir" under the coil, which is the very thing that makes it so hard to use on the XL. Any specific tips?
Smilee, watch out for the ice!
Last edited:
I have found a wide bore hole drip tip eliminates the spitting while breaking in the 357 after its good and broken in the spitting stops . As for the resevoir I think this is plus less time spent feeding . For me I spent time learning how much juice it takes to fill the 357 once you get that down you're good to go
Sent from my SPH-D700 using Tapatalk
Is a HH.357 Cisco Spec Hybrid Atomizers really the atty to end all attys
and would I want to try a custom, normal or a long barrel.....LOL..am I going shooting
and would I want to try a custom, normal or a long barrel.....LOL..am I going shooting
Is a HH.357 Cisco Spec Hybrid Atomizers really the atty to end all attys
They are pretty good I've only tried the normal 510 and the 901s hanna sent me a custom vg 357 but I haven't got it yet it should be tomorrow . Imo they out perform anything I have tried and better taste
Sent from my SPH-D700 using Tapatalk
Kami, I'll chime in. I've had a couple of them since H bomb first came out with them. They are dear, so I don't use them all that often. More of a special treat vape. They ARE that good, imo. I've got the normal 510's. (one sealed and one open)
Smilee, I'm so excited for you!!!! Please be sure to have some low nic on hand!
Smilee, I'm so excited for you!!!! Please be sure to have some low nic on hand!
Is a HH.357 Cisco Spec Hybrid Atomizers really the atty to end all attys
If you vape a PG/VG mix then the HH.357 510 Long Barrel would be the way to go. If you are 100% PG or 100% VG, I'd recommend the "custom" one that has the internals set for the juice type you use.
I have a short barrel and a long barrel, both 2.0 ohm. The short barrel doesn't see nearly as much action as the long barrel.
Congratz min Jong! ;o)
i've written a vmod XL review into the biggest german forum: my vmod XL
i've written a vmod XL review into the biggest german forum: my vmod XL
All i gotta say is Thank God for this pic!
The O-Ring came out and was giving me probs for a sec after I wanted to switch out my silo for my 1.5 ohm Hybrid. I went to wipe the catch cup and (PLOP!) Out comes the O- Ring. haha
Idiot! I grabed a plastic toothpick and the mad science began. Spent about 10 minutes searchin the threads and found it. So Thanks to AG and Kat for spamming that pic a few times. It caught my eye and i instantly began to read my little head off
The O-Ring came out and was giving me probs for a sec after I wanted to switch out my silo for my 1.5 ohm Hybrid. I went to wipe the catch cup and (PLOP!) Out comes the O- Ring. haha
Idiot! I grabed a plastic toothpick and the mad science began. Spent about 10 minutes searchin the threads and found it. So Thanks to AG and Kat for spamming that pic a few times. It caught my eye and i instantly began to read my little head off
- Status
Similar threads
- Locked
- Locked
